Roller doors

Buy an electric carport roller shutter or small roller door up to 400 cm wide for retrofitting in our configurator. Can be used as a carport roller door with a curtain weight of up to 20 kg. Available as Creato (round box) or Conturo (bevelled box). System supplier HEROAL®, made up by Reflexa®. Elero® motors with electronic limit switching as standard. Aluminium profile as standard. Wide choice of colours. Tested and certified roller shutters. You can use these roller shutters for indoor or outdoor fitting – also for patio doors and large window fronts. Advantages and features at a glance: - German Elero® RolTop D+ motors (electronic limit setting), no need to set the end positions - alternatively equivalent Somfy motors, depending on stock availability - also available with battery solar drive (including radio remote control and solar panel) - also available with crank drive (with removable crank) - made in Germany - hail impact tested, foam-filled aluminium curtain 52 mm high x 13.5 mm to DIN (MAXI profile) - Energy Label - larger possible sizes (up to 400 cm wide at 220 cm height, or 220 cm wide and 350 cm high) - integrated anti-lift protection through fixed shaft connectors - extruded bottom rails with rubber seal - 5-sided Conturo R box (bevelled at the front) or Creato R half-round box at no extra charge - sturdy CL 53 guide rails = 53 mm wide x 22 mm deep (piping insert for noise reduction) - optionally CL 68 rail type at no extra charge = 68 mm wide x 26.5 mm deep (greater curtain insertion depth) - box roll-formed as standard, extruded on request - box height always 20.5 cm - 60 mm octagonal steel shaft with bearing-mounted aluminium end cap - all RAL box and rail colours can be ordered at no extra charge - up to 265 cm wide x 273 cm high also usable as a roller door, as the curtain weight is below 20 kg - no fixings for the building structure are included in the delivery According to Reflexa, its roller shutters are made in Germany. The HEROAL® HSM 52 aluminium profile is filled with high-quality foam and has a face of 52 mm x 13.5 mm (measured without locking) The following curtain colours are available: This product is made to measure to your specifications and cannot be returned or exchanged. The order sizes are always the overall dimensions. Outer edge of guide rail to outer edge of guide rail = order width Top edge of box to bottom edge of bottom rail = order height The guide rails are 53 mm or 68 mm wide per side. The box height is always 20.5 cm

Buy made-to-measure replacement roller door curtains from system manufacturer Heroal, with free shipping. Here you can order HEROAL replacement curtains for roller doors. We offer 3 different curtain types for different applications. The maximum sizes for each are listed in the configuration. The curtain is delivered with steel suspension springs and pre-locked. The curtain is finished at the bottom with a thin rubber lip on the RS52 and a thick OSE rubber lip on the RD75. Everything is made to measure and ready to install. Largest application size = 550 cm wide by 450 cm high The following colours are available: Or 11 profile colours coated in special RAL colours, at NO extra cost: Simply order your roller door curtain or replacement curtain in our shop, made to measure in a wide choice of colours and curtain types.

Configure this high-quality, certified and tested HEROAL® RG 90 roller grille here at Sonnenschutzshop24 and order it. Our RG 90 roller grille is made from an extruded aluminium grille by the system supplier HEROAL®. Max. width = 460 cm x max. height = 360 cm (outer dimensions of the box system). You can put this roller grille together in our shop configurator and receive a price immediately. All extras in the price list can be ordered. Roller grilles make access to windows and doors more difficult and are increasingly used by private households to secure their homes. The standard specification complies with the latest certifications, as follows: - HEROAL® grille profile, 90 x 14 mm, 8 kg per m², ready to fit - integrated BECKER® / RADEMACHER® 230V tubular motor (subject to stock availability) - choice of surface-mounted or flush-mounted switch with dead-man function - fall protection - H-STF guide rail, 85 mm wide x 28 mm deep (noise-dampened) - box size 30 x 30 cm, roll-formed with lead-in rollers, 125 cm steel shaft - extruded aluminium bottom rail with 4 cm OSE rubber seal - supplied with straight grille pattern as shown - fixing screws for the building structure are not included Available colours: - box and rail colour in white, grey, silver, dark brown, light beige, cream white - grille colours in white, grey, silver, dark brown Our roller grilles use Heroal® profiles. The PREMIUM RG 90 is supplied as standard exclusively with BECKER® or RADEMACHER® motors. Fitting options: These roller grilles can be fitted in several ways. Summary of winding direction: - if the box faces outwards (left roller), the curved side of the grille always faces inwards - if the box faces inwards (right roller), the curved side of the grille always faces outwards All available accessories, such as switches, keypads, emergency crank option etc., can be found in the configuration. We deliver in secure packaging with 2 cm thick timber all round and a viewing window so that you can inspect the goods on delivery. Put together your RG 90 roller grille in our shop and order it with our configurator. Suitable for commercial and private use.

Configure the aluminium roller door HRT05 and buy it made to measure online. Certified up to 250 cm wide x 250 cm high clear opening. (Tested according to HEROAL® certificate RT05, profile Maxi 52) Roller door LIGHT HRT05 with 52 mm Heroal aluminium profile, assembled by Reflexa in Germany. The certificate is available at the bottom of this page. Max. outer dimensions 265 cm wide x 273 cm high. German PREMIUM equipment in many colours. Box size 21 x 21 cm, bevelled at the front or, alternatively, semi-circular at no extra charge. (Picture of the door shows fitting variant 2 = behind the opening, box facing inwards. The rear box panel and guide rails are not visible from outside; the convex side of the curtain faces outwards.) All the important details of the HRT05 roller door These roller doors come as standard with a robust, high-quality integrated mechanical 230 V elero® tubular motor. No fall arrest device is needed because the curtain weighs less than 20 kg, in line with HEROAL® certificate RT05 (available as a PDF at the bottom of the page). They can optionally be operated by BECK-O-TRONIC® radio control or by a switch only. Other circuits, such as yard lighting, can also be connected to the BECK-O-TRONIC®. The BECK-O-TRONIC® has an additional manual switch function. (The description is also available as a PDF at the bottom of the page.) The LIGHT HRT05 has a 1 cm hard rubber seal on the extruded bottom profile. Certificate RT05 (see link at the very bottom), together with the associated DIN standards for doors, is met because the curtain weight does not exceed 20 kg up to a size of 250 x 250 cm. A fall arrest device is therefore not required. The foam-filled aluminium curtain (face = 52 mm high x 13.5 mm thick to DIN) is fitted like a conventional roller shutter in, behind or in front of the reveal opening. We are happy to send you fitting notes for this roller door on request. The 21 cm high x 21 cm wide box (bevelled at 45 degrees at the front) is attractive and blends in with any façade. The keder-guided rails measure 28 mm deep and 68 mm wide and allow the curtain to run almost silently. These doors are supplied pre-assembled with the curtain rolled in. Screws for fixing to the building are not included. Roller door order sizes: drive side always viewed from inside. Top edge of box to bottom edge of bottom rail = order height Outer edge of rail to outer edge of rail = order width Steel springs suspending the curtain inside the box on a sturdy 60 mm steel shaft differ from conventional roller shutter shafts in their greater stability and durability. The bottom slat of the door is finished with a standard rubber lip that compensates for slight unevenness in the floor. Our view: high-quality German Heroal® branded product and an economical option for small garage doors that are easy to install yourself. Suitable for widths up to 265 cm and heights up to 270 cm. Box and rail colour available in any RAL colour at no extra charge. Aluminium slat dimensions: Fitting variants: These roller doors can be fitted in several ways. Summary of winding direction: - if the box faces outwards (left roller), the convex side of the curtain always faces inwards - if the box faces inwards (right roller), the convex side of the curtain always faces outwards Important note on the garage: - the garage must be closed on all sides once the door has been installed (if the garage is open at the back, the increased wind load can push the curtain backwards out of the guide rails) We deliver with our own factory vehicles in secure packaging. ***Restriction: these doors are not suitable as high-speed doors or for operation every minute (supermarkets, loading bays etc.). Every tubular motor has a thermal switch and shuts the system down in the event of overload or overheating.

The high-quality RD75 roller door from HEROAL is extremely versatile and can be built in large widths and heights. Configure it here and buy online. Up to 595 cm wide – simply configure and order online. This door stands out for its high quality. Suitable for large garages as well as commercial premises. Roller door PREMIUM H75 (Heroal RD75), Heroal RD75 aluminium profile. You can order this roller door in our roller door configurator. We also deliver to Switzerland and Austria as well as selected EU countries. Overview of new features and colours – Heroal RD75 roller door - maximum size with box up to 595 cm wide x 286 cm high, or 445 cm wide x 411 cm high - or roller door up to 620 cm wide without box (please click) Picture left = RD75 door in box, picture right = RD75 door, open installation without box, up to 620 cm wide (see RD75 XXL open configurator) (at 620 cm wide = wind class 2, up to 480 cm wide = wind class 4) Since 1 January 2018 we have been offering special and oversized versions of the HEROAL® RD75 system without box, with roll-up system, up to a total area of 21 square metres. Supplied with a special 150 Nm motor. - new entry guides and curtain side claws in the rails (rail dimensions = 37 mm deep x 100 mm wide) - storm protection thanks to interlocking curtain claws - this is the only way to make widths over 6 m technically possible - hail-tested (the curtain cannot be pushed out thanks to the S-lock, see picture, red circle) - even better noise reduction thanks to additional insulation in the box - all boxes with extra-strong steel side caps (no die-cast aluminium) (The picture of the door shows installation variant 2 = behind the opening, box facing inwards. The rear box cover and guide rails are not visible from outside; the convex side of the curtain faces outwards) As standard, these doors are fitted with a robust, integrated mechanical 230 V BECKER® / RADEMACHER® tubular motor (depending on stock availability) including fall arrest, and can optionally be operated by BECK-O-TRONIC® radio control or by switch only. Other circuits, such as yard lighting, can also be connected to the BECK-O-TRONIC®. All PREMIUM doors come with a sturdy aluminium bottom rail with a strong rubber seal. With roller doors, fall arrest is not an option but a requirement. The rubber seal at the bottom is approx. 4 cm high and has a rain drainage profile. To prevent the rubber seal from being completely crushed when the door closes and breaking after a while, as happens with inferior designs, we fit special stop blocks at the bottom of the side guide rails that stop the rubber from being squashed and damaged. Fixing screws into the building structure are not included. The foam-filled aluminium curtain (face = 75 mm high x 20 mm thick to DIN, 5.7 kg per m²) is installed in / behind / in front of the reveal opening just like a conventional roller shutter. Special slats, such as vision and ventilation profiles, are available. (see configuration) The original installation instructions from the system supplier HEROAL® (please click) The 30 cm or 37 cm high box (both box sizes are fully enclosed, front bevelled at 45 degrees) is attractive and blends in easily with any façade. The keder-guided rails measure 37 mm deep and 100 mm wide and allow the curtain to run almost silently. - total height of the roller door up to 300 cm = 30 cm fully enclosed box (with steel side caps) - total height of the roller door over 300 = 37 cm high fully enclosed box (with steel side caps) Roller door order sizes: drive side always viewed from inside. Top edge of box to bottom edge of bottom rail = order height Outer edge of rail to outer edge of rail = order width Steel springs hold the curtain inside the box on a sturdy 70/125 mm steel shaft (70 mm for the 30 cm box); they differ from conventional roller shutter shafts in their greater stability and durability. As standard, the bottom rail has a strong rubber seal that compensates for uneven floors. The optional radio control plugs into an existing socket and is self-learning. It really could not be simpler. Our view: High-quality German Heroal® branded product and a cost-effective option for large professional doors for self-installation* Widest range of application, up to 620* cm wide and up to 400* cm high.(*max. area 17 m² = certified) *Please note: these roller doors are delivered dismantled. Due to the weight, the curtain is not pre-fitted in the box and must be installed on site. They are therefore only suitable for tradespeople with sufficient technical understanding. The box is placed on the rails and fixed. The pre-locked curtain is then simply slid over the shaft and attached with steel springs. Done. Box and rail colour available in white - grey - brown - silver H75 aluminium slat = 5.7 kg per m², 75 mm x 20 mm face to DIN. 11 profile colours to choose from at no extra cost: Installation variants: These roller doors can be installed in different ways. Summary of winding direction: - if the box faces outwards (left-hand roll), the convex side of the curtain always faces inwards - if the box faces inwards (right-hand roll), the convex side of the curtain always faces outwards All available accessories, such as radio controls, switches, keypads, emergency crank option etc., can be found in the configuration. Important note on the condition of the garage: - the garage must be closed on all sides once the door has been installed (if the garage is open at the back, the increased wind load can push the curtain backwards out of the guide rails) We deliver in secure packaging with 2 cm thick timber all round and a viewing window so you can inspect the goods on delivery. Please note: - up to a size of 450 cm we deliver free to kerbside - sizes from 451 cm wide are delivered free to address Free to address means that the customer must help unload the goods from the lorry. From these sizes upwards, the carriers are no longer able to unload the large packages on their own. At maximum order sizes, the total weight including packaging can be up to 180 kg. We recommend arranging for a total of 3 helpers to be available at short notice to unload the goods. ***Restriction: These doors are not suitable as high-speed doors or for operation every few minutes (supermarket, loading bay etc.). Every tubular motor has a thermal switch and shuts the system down in the event of overload / overheating. Price of the RD75 roller door Of course you will always find cheaper prices for roller doors online. Quality is what matters most with large roller doors, so that you do not get any unpleasant surprises after buying. Wind load, certification, stability and durability are decisive when buying a roller door.

The high-quality RD75 XXL roller door without box is even more versatile and can also be made in oversizes. This door, too, is built to high quality standards. Available to buy online. Can be made 560 cm wide x 320 cm high and larger. This system allows the largest possible sizes. As there is no box, we recommend fitting it behind the reveal from the inside. Otherwise, a protective box should be planned in during construction. German PREMIUM specification in many colours. New since 2018: maximum sizes and coil diameters in cm: - max. door width up to 370 cm at max. 538 cm overall height (coil = approx. 39 cm) - max. door width 395 cm at max. 512 cm overall height (coil = approx. 37.5 cm) - max. door width 420 cm at max. 487 cm overall height (coil = approx. 37.3 cm) - max. door width 445 cm at max. 462 cm overall height (coil = approx. 37.1 cm) - max. door width 470 cm at max. 437 cm overall height (coil = approx. 37 cm) - max. door width 495 cm at max. 411 cm overall height (coil = approx. 36 cm) - max. door width 520 cm at max. 386 cm overall height (coil = approx. 35.5 cm) - max. door width 545 cm at max. 355 cm overall height (coil = approx. 34 cm) - max. door width 570 cm at max. 335 cm overall height (coil = approx. 35 cm) - max. door width 595 cm at max. 309 cm overall height (coil = approx. 34 cm) - max. door width 620 cm at max. 309 cm overall height (coil = approx. 34 cm) RD H75 door, open installation without box, up to 620 cm wide (at 620 cm width = wind class 2, up to 480 cm width = wind class 4) From approx. 17 m² = version with special 150 Nm motor. From this area upwards, doors are manufactured and supplied without wind load certification. Roll-on system from a height of 411 cm included at no extra cost - new entry guides and curtain end locks in the rails (rail dimensions = 37 mm deep x 100 mm wide) - storm protection thanks to interlocking curtain - hail-tested (the curtain cannot be pushed out thanks to the S-lock, see the red circle in the picture) - even better noise insulation thanks to additional insulation in the box - all boxes with extra-strong steel end caps (not die-cast aluminium) (the picture of the door shows fitting variant 2 = behind the opening, box facing inwards. The rear box cover and guide rails are not visible from the outside; the curved side of the curtain faces outwards) As standard, these doors are fitted with a robust, integrated mechanical 230V BECKER® / RADEMACHER® tubular motor (depending on stock availability) including a fall arrest device, and can optionally be operated by BECK-O-TRONIC® radio control or by switch only. Other circuits, such as yard lighting, can also be connected to the BECK-O-TRONIC®. All PREMIUM doors come with a sturdy aluminium bottom rail with a strong rubber seal. On roller doors, a fall arrest device is not an option but a requirement. The rubber seal at the bottom is approx. 4 cm high and has a rain drainage profile. To stop the seal from being completely crushed when closing and breaking after a while, as happens with inferior products, we fit special stop blocks at the bottom of the side guide rails that prevent the rubber from being squashed and damaged. Fixing screws into the building structure are not included. The foam-filled aluminium curtain (face = 75 mm high x 20 mm thick to DIN, 5.7 kilograms per m²) is fitted in / behind / in front of the reveal opening just like a conventional roller shutter. Special slats, such as vision and ventilation profiles, are available. (see configurator) Original fitting instructions from the system supplier HEROAL® (click here) The guide rails with keder guidance measure 37 mm deep and 100 mm wide and allow the curtain to run almost silently. Roller door order sizes: drive side always viewed from inside. Top edge of bracket to bottom edge of bottom rail = order height Outer edge of rail to outer edge of rail = order width Steel springs suspend the curtain inside the box on a sturdy 70/125 mm steel shaft; they differ from conventional roller shutter shafts in their greater stability and durability. As standard, the bottom rail has a strong rubber seal that compensates for uneven floors. The optional radio control plugs into an existing socket and is self-learning. It really could not be simpler. Our view: High-quality German Heroal® branded product and a cost-effective option for large professional doors for self-installation* Widest range of sizes, up to 620* cm wide and up to 538* cm high.(*max. area 17 m² = certified) *Please note: these roller doors are delivered disassembled. For weight reasons, the curtain is not pre-fitted in the box and must be installed on site. They are therefore only suitable for tradespeople with sufficient technical understanding. The box is placed on the rails and fixed. The pre-locked curtain is then simply slid over the shaft and secured with steel springs. Done. Aluminium slat = 5.7 kilograms per m²: Rail colour available in white - grey - brown - silver 11 profile colours to choose from at no extra cost: Fitting variants: These roller doors can be fitted in different ways. Summary of winding direction: - if the coil faces outwards (left-hand roll), the curved side of the curtain always faces inwards - if the coil faces inwards (right-hand roll), the curved side of the curtain always faces outwards All available accessories, such as radio controls, switches, keypads, emergency crank options etc., can be found in the configurator. Important note on the garage: - the garage must be closed on all sides once the door is fitted (if the garage is open at the back, the increased wind load can push the curtain backwards out of the guide rails) We deliver in secure packaging with 2 cm thick timber all round and a viewing window so the goods can be checked on delivery. Please note: - up to a size of 450 cm we deliver kerbside - sizes from 451 cm width are delivered to the address Delivery to the address means that the customer must help unload the goods from the lorry. From these sizes upwards, the carriers can no longer unload the large packages on their own. At maximum order sizes, the total weight including packaging can be up to 180 kg. We recommend having a total of 3 helpers available at short notice to unload the goods. ***Limitation: These doors are not suitable as high-speed doors or for operation every minute (supermarkets, loading bays etc.). Every tubular motor has a thermal switch and shuts the system down in the event of overload / overheating.

Buy the H55 roller door with fall arrest device from system supplier Heroal here. PREMIUM specification. For electric roller doors, the order sizes are calculated from the outside-edge width and outside-edge height. For maximum safety, always supplied with a fall arrest device. (The illustration shows fitting option 2 = behind the opening, box facing inwards. The rear box cover and guide rails are not visible from outside; the convex side of the curtain faces outwards.) As standard, our roller doors are fitted with a robust, high-quality integrated mechanical 230 V BECKER® / RADEMACHER® tubular motor (depending on stock availability) including a fall arrest device, and can optionally be operated by BECK-O-TRONIC® radio control or by a switch only. Other circuits, such as yard lighting, can also be connected to the BECK-O-TRONIC®. Our doors use Heroal® aluminium profiles. As standard, the SMART H55 has a 4 cm rubber seal on the aluminium bottom rail. For roller doors weighing over 20 kg, a fall arrest device is not an option but a requirement. The foam-filled aluminium curtain (face = 52 mm high x 13.5 mm thick to DIN) is fitted like a conventional roller shutter in, behind or in front of the reveal opening. These doors are supplied fully pre-assembled with the curtain rolled up. Fixing screws into the building structure are not included in the scope of delivery. We are happy to send you fitting notes for this roller door on request. The 23 / 25 or 30 cm high box (bevelled at 45 degrees at the front) has a clean shape and suits any façade. The keder-guided rails measure 28 mm deep and 85 mm wide and allow the curtain to run almost silently. Box heights: - up to 300 cm door width x 250 cm door height = 23 x 23 box size - up to 300 cm overall door height = 25 x 25 cm box size, above that 30 x 30 cm Roller door order sizes: drive side always viewed from inside. Top edge of box to bottom edge of bottom rail = order height Outer edge of rail to outer edge of rail = order width Steel springs suspending the curtain inside the box on a sturdy 60/70 or 125 mm steel shaft differ from conventional roller shutter shafts in their greater stability and durability. As standard, the aluminium bottom slat of the door has a 4 cm thick rubber lip with a rain drainage profile in the extruded aluminium section (see picture on the left), which compensates very well for uneven floors. To prevent the rubber seal from being completely crushed when the door closes and breaking after a while, as happens with inferior designs, we fit special stop blocks at the bottom of the side guide rails that stop the rubber from being squashed and damaged. With the OSE safety edge option with electronics, the same aluminium bottom rail system is used. The only difference is that in this case it contains the sensors for the OSE control. If no OSE rubber seal is required, we supply an ECO seal with a 1 cm rubber profile in the last slat at a reduction of EUR 29. Our view: High-quality German Heroal® branded product and a cost-effective option for small garage doors that are easy to install yourself. Can be made in any width from 160 cm to 400 cm and up to 320 cm high. (*Special heights up to 370 cm can be made; in the configurator these can be ordered up to a width of 320 cm) Box and rail colour available in white - grey - brown - silver or in a RAL colour = plus 20% surcharge Aluminium slat dimensions: Fitting options: These roller doors can be fitted in different ways. Summary of winding direction: - if the box faces outwards (left roller), the convex side of the curtain always faces inwards - if the box faces inwards (right roller), the convex side of the curtain always faces outwards. All available accessories, such as radio controls, switches, keypads, emergency crank option etc., can be found in the configuration. Important note on the condition of the garage: - the garage must be closed on all sides once the door is installed (if the garage is open at the back, the increased wind load can push the curtain backwards out of the guide rails) - when fitting 2 doors to one opening, we recommend the RD75 door system with the curtain interlocked inside the guide rails We deliver in secure packaging with 2 cm thick timber all round and a viewing window so you can inspect the goods on delivery. ***Restriction: These doors are not suitable as high-speed doors or for minute-by-minute operating cycles (supermarket, loading bay etc.). Every tubular motor has a thermal switch and shuts the system down in the event of overload / overheating. Order your high-quality motorised garage roller door with aluminium slats here in the roller door configurator up to 400 cm wide. Delivery to Switzerland, Austria and selected EU countries is possible.