Advice +49 9732 3023858 · Mon–Thu 9 am–4 pm, Fri 9 am–2 pm shop@sonnenschutzshop24.eu Free shipping within Germany (except islands/freight) Shop rating: 4,83 out of 5 · 282 reviews on ProvenExpert
Go to homepage
Send a message
€0.00

Made-to-measure sun protection

Roller door PREMIUM RD75 up to 600 cm wide made to measure

Shop rating: 4,83 out of 5 · 282 reviews on ProvenExpert
  • Width up to 595 cm, height up to 412 cm
from €2,118.72
incl. VAT · free shipping within Germany (except islands)
Delivery time 2 weeks
Configure now Advice +49 9732 3023858
Free shipping within Germany (except islands)
Payment by prepayment (bank transfer)
24 months statutory warranty
Expert advice Mon–Fri · +49 9732 3023858

Configurator

Roller door PREMIUM RD75 up to 600 cm wide in 3 steps

Choose step by step. The price updates with every change, and you can change completed steps at any time.

cm
Info and measuring guide

Please state in cm.

Every door is made to measure.

Measuring guide for roller doors

Our sizes are outer edge dimensions.

Depending on the type of installation, the rail widths as well as box heights and bottom rails must be added.

Example door ROLLUX 500:

Installation type 1 = in the opening

- Your clear dimensions (garage opening dimensions) are e.g. 410 cm wide by 250 cm high.

You want to install in the opening (type 1).

The passage dimensions are reduced by the two guide rail widths (2 x 9.5 cm)

This leaves a passage width of 391 cm.

The passage height is reduced by the box height of 30 cm up to 300 cm overall height and 37 cm up to 380 cm overall height, and by the bottom rail of 8 cm,

which does not roll into the box.

This leaves a passage height of 250 cm - 30 cm - 8 cm (with OSE - 10 cm) = 212 cm.

--------------------------------------------------------------------------------

Installation type 2 or 3 = behind or in front of the opening

It is therefore advisable to install behind the reveal opening (type 2) or in front of it (type 3)

in order to retain the passage dimensions of the garage opening.

The measuring for type 1 or type 3 is the same.

Add the box dimension of 30 cm or 37 cm + 8 cm bottom rail (with OSE + 10 cm) to your clear opening height.

The order height would therefore be 250 cm + 30 cm + 8 cm (with OSE + 10 cm) = 288 cm.

Please add 2 x rail dimension = 19 cm to your clear passage width. The order width would therefore be 429 cm.

cm
Info and measuring guide

Box sizes:

- Box dimension 30 x 30 cm (closed all round)

- Box dimension 37 x 37 cm (closed all round)

Order height = from top edge of box to bottom edge of bottom rail

Order width = outer edge of guide rail to outer edge of guide rail.

Roller door in box possible up to max. 575 cm width.

Max. heights as follows:

- up to 345 cm width = max. height = 411 cm (up to 305 cm height = 30 box)

- up to 420 cm width = max. height = 411 cm (up to 255 cm height = 30 box)

- up to 520 cm width = max. height = 336 cm (up to 255 cm height = 30 box)

- up to 595 cm width = max. height = 286 cm (up to 255 cm height = 30 box)

The first-mentioned sizes can be built with a 37 box. Alternatively available without box.

Queries: Germany 09732 3023858

-----------------------------------------------------------------

Our finished dimensions are outer edge dimensions.

Depending on the installation type, the rail widths as well as the box height and bottom rail must be added.

Example door PREMIUM RD75:

Installation type 1 = in the opening

- Your clear dimensions (garage opening dimensions) are e.g. 380 cm wide by 310 cm high = order dimensions 379 cm wide by 309 cm high

You want to install in the opening (type 1).

The passage dimensions are reduced by the two guide rail widths (2 x 10 cm)

This leaves a passage width of 360 cm

The passage height is reduced by the box height of 37 cm and the bottom rail of 8 cm, which does not roll into the box.

This leaves a passage height of 310 cm

- 37 cm - 8 cm (with OSE - 10 cm) = 265 cm

--------------------------------------------------------------------------------

Installation type 2 or 3 = behind or in front of the opening

It is therefore advisable to install behind the reveal opening (type 2) or in front of it (type 3)

in order to retain the passage dimensions of the garage opening.

The measurement for type 2 or type 3 is the same.

Add the box dimension of 37 cm + 8 cm bottom rail (with OSE + 10 cm) to your clear opening height.

The order height would therefore be 310 cm

+ 37 cm + 8 cm (with OSE + 10 cm) = 355 cm

To your clear passage width of 380 cm, please add:

2 x rail dimension = 20 cm. The order width would therefore be 400 cm.

How to measure

Measuring guide for variant 1: Installation directly in the reveal opening. The box faces inwards. The convex side of the curtain faces outwards. Please measure the clear width at the top, bottom and in the middle. Deduct 0.5–1 cm from the smallest measurement. This is the finished width. (order width)

The finished height is the clear height from the top of the reveal (where the box will be) to the floor, minus 0.5–1 cm. (order height)


Variant 2: Installation behind the reveal opening (if there is space). The box faces inwards, see original picture. The convex side of the curtain faces outwards. Measure as follows: add 20 cm (2 x rail width of 100 mm per side) to the width of the reveal opening. Order height = top edge of box to bottom edge of bottom rail. The advantage of this type of installation is that the clearance height does not change. (if there is space above the reveal opening)


Variant 3: Installation in front of the reveal opening (as variant 2, but the box faces outwards and the convex side of the curtain faces inwards): please state "Type 3" when ordering.

Phone: +49 9732 3023858 · Mon–Thu 9 am–4 pm, Fri 9 am–2 pm

Motor type
Info and measuring guide

We supply drives and controls from the German manufacturers BECKER® and RADEMACHER® (depending on stock availability). Drive side always as seen from inside.

Motor type Motor type Motor type Motor type

Internal emergency crank gear incl. 150 cm hand crank

(the type of fitting is adapted to the installation method)

Motor type

This asks on which side, seen from inside, the motor cable should be.

Depending on your choice, the tubular motor will then be installed at this position.

Always state the motor side as seen from inside, regardless of which installation method you use.

The BECKER® radio control is supplied with a 2-channel hand transmitter.

If you need more hand transmitters, please select them under Extras.

We only install BECKER® motors.

Box colour

The colour dots show an approximate shade – screen colours may differ from the original.

Info and measuring guide

RAL special colours have a delivery time of approx. 4-7 weeks.

System in the box

Box colour
Shutter curtain colour

The colour dots show an approximate shade – screen colours may differ from the original.

Info and measuring guide

You can order curtains in the following colours:

Shutter curtain colour
Vision slats
Special slat with plastic viewing window.
flat cut-out special slat for ventilation
Fitting type
Info and measuring guide

Measuring instructions for type 1: Please measure the clear width at the top, at the bottom and in the middle.

Deduct 0.5 cm from the smallest dimension. This is the finished width.

The finished height is the clear height from the top edge of the reveal (where the box will ultimately be) to the floor.

Version 1: Installation directly in the reveal opening, measuring as described above.

Fitting type

Version 2: Installation behind the reveal opening (if there is space), measuring as follows: Please add 20 cm (2 x rail dimension) to the width of the reveal opening.

Order height = top edge of box to bottom edge of guide rail. The advantage of this type of installation is that the passage height does not change. (if there is space above the reveal opening)

Fitting type

Version 3: Installation in front of the reveal opening (like version 2, but the box faces outwards): Please state "Type 3" when ordering.

OSE bottom rail
Info and measuring guide

- In accordance with current EU regulations, roller doors operated by radio remote control must be fitted with a so-called OSE bottom edge with electronics (optical sensor bottom rail).

This regulation applies to doors in public places just as it does to doors on commercial premises etc.

However, an OSE bottom rail with electronics only makes sense with radio remote control. In all other cases, such as switches or key switches, it is the responsibility of the person operating the switch to move the door.

The old rule, under which so-called DW bottom rails (pressure wave rails) were also permitted, is no longer valid.

These considerably cheaper bottom rails are still frequently offered by competitors.

- As a retrofitted safety extra for roller doors without OSE electronics, we recommend installing a light barrier on radio-operated doors. This serves a similar purpose: if the roller door is lowered unattended by radio while there are obstacles, animals or children underneath, the roller door stops and does not unroll any further.

The difference from the OSE bottom edge with electronics is that in an emergency the door does not automatically reverse (as is the case with OSE electronics) but simply stops.

What private individuals ultimately install on their own property is up to each of them.

A 4 cm high OSE rubber seal with rain drainage profile is standard.

Optionally with OSE electronics in accordance with DIN, in combination with a radio control.

OSE bottom rail
Emergency crank gear
Info and measuring guide

In the event of a power failure, the door can still be operated by crank. An additional gear is fitted on the shaft.

With installation type 3, in front of the opening, the crank inlet on the box is closed with a rubber plug so that unauthorised opening is not possible. In an emergency, the rubber plug must then be removed and the crank can be inserted from outside to operate the door manually.

Crank operation can be chosen freely, either from outside or from inside. We manufacture to your requirements.

Emergency crank gear

Please note: image is for illustration only. Variations are possible.

Extras
Info and measuring guide

- required if you want to install a door without safety extras such as a light barrier or OSE edge, but with 2 switches (push button inside, e.g. key switch outside)

This isolating relay is a flush-mounted version and only needs to be connected in between if the switches are wired for SELF-HOLDING (switch function latches permanently), in order to avoid short circuits. You can avoid this type of connection by installing the switches not with self-holding but only with a push-button/dead-man function.

Our switches are supplied with a push-button/dead-man function and can be switched over.

Explanation of dead-man control:

The operator keeps the switch pressed until the door has been raised or lowered.

Explanation of the self-holding function:

The operator presses the switch once and the motor runs through to the respective end position.

In conjunction with a BECKOTRONIC 5 radio roller door control and an additional switch, no separate isolating relay is needed, because the control itself takes care of this. An additional switch connection is provided on the control.

If you select "wired code keypad", NO isolating relay is required when connecting an additional switch.

Info and measuring guide

If you would like a code keypad for outside, this is only possible by means of a radio control.

In this case you will receive a radio-operated code keypad on which you can set any number combination. The advantage of this combination is that you do not necessarily need a "misplaced" hand-held transmitter to open the door system. Any user who enters the preset number combination can open the door from outside.

As the commands are transmitted from the code keypad to the control exclusively by radio, there is also no need for complex wiring.

There is also a manual switch on the control itself. An additional switch for inside is therefore not necessary.

When using a normal switch and a key switch, please note when connecting that a multi-point isolating relay must be connected in between. If no relay is used, there is a risk of damage to the roller door motor. Your authorised electrician should advise you on this. For an explanation and ordering option, see the selection field EXTRAS.

AP = surface-mounted

UP = flush-mounted

The roll-on system relieves the load on the rollers in the box.

The special slats are always fitted in the upper third.

If more than one special slat is fitted, they are inserted so that each special slat is always followed by a normal curtain slat. This is for stability reasons and to meet the certification requirements of the system provider Heroal®.

Call-back service
Inspection log book
Info and measuring guide

- this is generally only required if the door is used commercially and is regularly inspected by official inspection bodies

- the so-called inspection log is not actually a book, but just individual sheets in which countless details about the door are recorded, such as serial number, motor number, fall-arrest device number, manufacturer, pulling force test etc.

Please complete all steps first.

Product description

The high-quality RD75 roller door from HEROAL is extremely versatile and can be built in large widths and heights. Configure it here and buy online. Up to 595 cm wide – simply configure and order online.

This door stands out for its high quality. Suitable for large garages as well as commercial premises. Roller door PREMIUM H75 (Heroal RD75), Heroal RD75 aluminium profile. You can order this roller door in our roller door configurator. We also deliver to Switzerland and Austria as well as selected EU countries.

Overview of new features and colours – Heroal RD75 roller door

- maximum size with box up to 595 cm wide x 286 cm high, or 445 cm wide x 411 cm high

- or roller door up to 620 cm wide without box (please click)


Picture left = RD75 door in box, picture right = RD75 door, open installation without box, up to 620 cm wide (see RD75 XXL open configurator)

(at 620 cm wide = wind class 2, up to 480 cm wide = wind class 4)

Since 1 January 2018 we have been offering special and oversized versions of the HEROAL® RD75 system without box, with roll-up system, up to a total area of 21 square metres. Supplied with a special 150 Nm motor.

- new entry guides and curtain side claws in the rails (rail dimensions = 37 mm deep x 100 mm wide)

- storm protection thanks to interlocking curtain claws

- this is the only way to make widths over 6 m technically possible

- hail-tested

(the curtain cannot be pushed out thanks to the S-lock, see picture, red circle)


- even better noise reduction thanks to additional insulation in the box - all boxes with extra-strong steel side caps (no die-cast aluminium)

(The picture of the door shows installation variant 2 = behind the opening, box facing inwards. The rear box cover and guide rails are not visible from outside; the convex side of the curtain faces outwards)

As standard, these doors are fitted with a robust, integrated mechanical 230 V BECKER® / RADEMACHER® tubular motor (depending on stock availability) including fall arrest, and can optionally be operated by BECK-O-TRONIC® radio control or by switch only. Other circuits, such as yard lighting, can also be connected to the BECK-O-TRONIC®.


All PREMIUM doors come with a sturdy aluminium bottom rail with a strong rubber seal. With roller doors, fall arrest is not an option but a requirement.

The rubber seal at the bottom is approx. 4 cm high and has a rain drainage profile. To prevent the rubber seal from being completely crushed when the door closes and breaking after a while, as happens with inferior designs, we fit special stop blocks at the bottom of the side guide rails that stop the rubber from being squashed and damaged. Fixing screws into the building structure are not included.

The foam-filled aluminium curtain (face = 75 mm high x 20 mm thick to DIN, 5.7 kg per m²) is installed in / behind / in front of the reveal opening just like a conventional roller shutter. Special slats, such as vision and ventilation profiles, are available. (see configuration)

The original installation instructions from the system supplier HEROAL® (please click)

The 30 cm or 37 cm high box (both box sizes are fully enclosed, front bevelled at 45 degrees) is attractive and blends in easily with any façade. The keder-guided rails measure 37 mm deep and 100 mm wide and allow the curtain to run almost silently.

- total height of the roller door up to 300 cm = 30 cm fully enclosed box (with steel side caps)

- total height of the roller door over 300 = 37 cm high fully enclosed box (with steel side caps)

Roller door order sizes: drive side always viewed from inside.

Top edge of box to bottom edge of bottom rail = order height

Outer edge of rail to outer edge of rail = order width

Steel springs hold the curtain inside the box on a sturdy 70/125 mm steel shaft (70 mm for the 30 cm box); they differ from conventional roller shutter shafts in their greater stability and durability. As standard, the bottom rail has a strong rubber seal that compensates for uneven floors. The optional radio control plugs into an existing socket and is self-learning. It really could not be simpler.

Our view: High-quality German Heroal® branded product and a cost-effective option for large professional doors for self-installation* Widest range of application, up to 620* cm wide and up to 400* cm high.(*max. area 17 m² = certified)

*Please note: these roller doors are delivered dismantled. Due to the weight, the curtain is not pre-fitted in the box and must be installed on site. They are therefore only suitable for tradespeople with sufficient technical understanding. The box is placed on the rails and fixed. The pre-locked curtain is then simply slid over the shaft and attached with steel springs. Done.


Box and rail colour available in white - grey - brown - silver

H75 aluminium slat = 5.7 kg per m², 75 mm x 20 mm face to DIN.


11 profile colours to choose from at no extra cost:


Installation variants: These roller doors can be installed in different ways.

Summary of winding direction:

- if the box faces outwards (left-hand roll), the convex side of the curtain always faces inwards

- if the box faces inwards (right-hand roll), the convex side of the curtain always faces outwards

All available accessories, such as radio controls, switches, keypads, emergency crank option etc., can be found in the configuration.

Important note on the condition of the garage:

- the garage must be closed on all sides once the door has been installed (if the garage is open at the back, the increased wind load can push the curtain backwards out of the guide rails)

We deliver in secure packaging with 2 cm thick timber all round and a viewing window so you can inspect the goods on delivery.


Please note:

- up to a size of 450 cm we deliver free to kerbside

- sizes from 451 cm wide are delivered free to address

Free to address means that the customer must help unload the goods from the lorry. From these sizes upwards, the carriers are no longer able to unload the large packages on their own. At maximum order sizes, the total weight including packaging can be up to 180 kg. We recommend arranging for a total of 3 helpers to be available at short notice to unload the goods.

***Restriction:

These doors are not suitable as high-speed doors or for operation every few minutes (supermarket, loading bay etc.). Every tubular motor has a thermal switch and shuts the system down in the event of overload / overheating.

Price of the RD75 roller door

Of course you will always find cheaper prices for roller doors online. Quality is what matters most with large roller doors, so that you do not get any unpleasant surprises after buying. Wind load, certification, stability and durability are decisive when buying a roller door.



Technology & fitting

Key data from the configurator

Sizes
Width up to 595 cm · height up to 412 cm
Delivery time
2 weeks

Instructions & downloads

Advice

Personal expert advice

Not sure about size, fabric or fitting? Call us or let us check your configuration before production.

+49 9732 3023858

Mon–Thu 9 am–4 pm, Fri 9 am–2 pm

Have my configuration checked

What customers say

4,83
Shop rating: 4,83 out of 5 · 282 reviews on ProvenExpert

Overall rating of our shop on ProvenExpert. As of 18.10.2026

All reviews on ProvenExpert

Reviews of this product

Roller door PREMIUM RD75 up to 600 cm wide
This website uses cookies to ensure the best experience possible. More information...