Window films

Solar film with a built-in dot pattern for bird protection Sentinel Silver 35 BFD 11 is a silver solar film with an integrated dot pattern: 11 mm dots on a 65 mm grid covering 2.25 % of the surface. Because the pattern is part of the film, it cannot discolour or come off dot by dot. In the WIN flight tunnel test II (AT), the manufacturer reports 13 % bird strikes; according to the manufacturer a silver mirror is usually above 70 %. The film is fitted externally, is easy to clean and, thanks to its special adhesive, can be removed without residue if needed. The film is supplied cut to your size (width × height). Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Visible light transmission (VLT): 34 % on 4 mm single glazing, 31 % on 4/12/4 mm double glazing Visible light reflection outside/inside: 41/37 % on 4 mm single glazing g-value (total solar energy transmittance): 0.33 on 4 mm single glazing, 0.28 on 4/12/4 mm double glazing Total solar energy rejected (90°): 67 % on 4 mm single glazing, 72 % on 4/12/4 mm double glazing UV protection (300–380 nm): over 99 %; fading protection 68 % on 4 mm single glazing Thickness: 75 µm; fire classification B/s1/d0 (test certificate EN 13823) Manufacturer's warranty: 10 years for vertical and 5 years for sloped installation – with all edges sealed

Bird protection for glass with a black dot grid WingSafe Black Dot makes glass visible to birds: 11 mm black dots are built into the film in a right-angled grid and cover 2.25 % of the surface. As the pattern is part of the film, it cannot discolour or come off dot by dot. In the ABC flight tunnel test (USA) the manufacturer measured 4 % bird strikes (“Bird Friendly”); it points out that real-world performance may differ depending on the position of the sun, reflections and other factors. It is fitted externally, is easy to clean and can be removed without residue if needed. The film is supplied cut to your size (width × height). Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Pattern: black dots, 11 mm, covered area 2.25 % Visible light transmission (VLT) in the clear area: 88 % on 4 mm single glazing UV protection (300–380 nm): over 99 % ABC flight tunnel test (USA): 4 % bird strikes Thickness incl. adhesive: 125 µm; fire classification B/s1/d0 (EN 13823) Manufacturer's warranty: 10 years for vertical and 5 years for sloped installation

Transparent colour films in red, blue, green and yellow The coloured CDF films let you tint glass after installation: the pane stays see-through but gains a strong colour – for glass partitions, for example, or as a design element. Available as CDF Red 25, CDF Blue 30, CDF Green 35 and CDF Yellow 80. Polyester film with a scratch-resistant surface and acrylic adhesive, fitted on the inside and removable without residue later. The film is supplied cut to your size (width × height); roll width: 152 cm. Manufacturer's note: if exterior panes are fully or partly covered, thermal stress can damage the glass; interior panes without sunlight or large temperature swings are not affected. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Colours: Red 25, Blue 30, Green 35, Yellow 80 Material: coloured polyester film, scratch-resistant surface, acrylic adhesive Fitting: inside Manufacturer's warranty: 5 years for indoor use

“Trichromic” design film that changes colour with the viewing angle CDF 1100 Trichromic is an effect film for interiors with special design requirements. Depending on the viewing angle and the light, its colour shifts between blue, purple and yellow (“flip-flop effect”). Polyester film with a scratch-resistant surface and acrylic adhesive, fitted on the inside. The film is supplied cut to your size (width × height); roll width: 152 cm. Manufacturer's note: if exterior panes are fully or partly covered, thermal stress can damage the glass; interior panes without sunlight or large temperature swings are not affected. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Effect: colour shift blue – purple – yellow depending on the viewing angle Material: polyester film, scratch-resistant surface, acrylic adhesive Fitting: inside Manufacturer's warranty: 5 years for indoor use

Striped sandblast-look film: 35 mm stripes, 10 mm gaps CDF 2304 is a transparent polyester film with partially printed stripes in a sandblasted look – 35 mm wide with 10 mm gaps. The pane stays see-through, but the pattern breaks up direct views and makes large glass areas such as partitions easier to see. The stripes run along the roll length. It is fitted on the inside and can later be removed without residue. The film is supplied cut to your size (width × height); roll width: 152 cm. Manufacturer's note: if exterior panes are fully or partly covered, thermal stress can damage the glass; interior panes without sunlight or large temperature swings are not affected. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Pattern: sandblast-look stripes, 35 mm wide, 10 mm gaps Direction: stripes run along the roll length Material: transparent polyester film, partially printed; acrylic adhesive Fitting: inside Manufacturer's warranty: 2 years for indoor use

Decorative films with sandblast-look patterns – stripes, waves, squares The CDF 2400 series comprises decorative films with sandblast-look patterns printed on a transparent polyester base. The pane stays see-through, but the pattern breaks up large glass areas, gives partial privacy and makes glass easier to see. Glazed Frost, a full-surface sandblast look, is also part of the series. The patterned films are fitted on the inside and can later be removed without residue. The film is supplied cut to your size (width × height); roll width: 152 cm. Manufacturer's note: if exterior panes are fully or partly covered, thermal stress can damage the glass; interior panes without sunlight or large temperature swings are not affected. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Glazed Frost: full-surface sandblast look, PVC, 80 µm, inside and outside Stripes: CDF 2401 (graduated, gaps 1–36 mm), CDF 2402 (graduated, gaps 3 mm), CDF 2403 (various widths), CDF 2404 (13 mm wide, gaps 6 mm) Waves: CDF 2450, 45 mm high, gaps 10 mm Squares: CDF 2460 (45 × 45 mm, gaps 10 mm), CDF 2461 (frosted surface with clear 20 × 20 mm squares, gaps 50 mm) Manufacturer's warranty: patterns 5 years indoors; Glazed Frost 7 years indoors, outdoors 3 years vertical, 1 year inclined

White dot grid for privacy and design CDF 2810 has a fine white dot grid: 3 mm dots with 1 mm spacing, arranged at 45°. The pane stays see-through, but views in are reduced and glass becomes easier to see. The direction of the pattern does not matter when cutting. Transparent polyester film, fitted on the inside, removable without residue later. The film is supplied cut to your size (width × height); roll width: 152 cm. Manufacturer's note: if exterior panes are fully or partly covered, thermal stress can damage the glass; interior panes without sunlight or large temperature swings are not affected. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Pattern: white dots 3 mm, spacing 1 mm, arranged at 45° Direction: not relevant Material: transparent polyester film, partially printed; acrylic adhesive Fitting: inside Manufacturer's warranty: 5 years for indoor use

Static-cling privacy film “Blast” – no adhesive CDFS 6001 Blast clings by static, without adhesive, so it is quick to put up and take down again – handy during renovation work or for a limited period. It diffuses light: a direct view through is prevented while the brightness is largely kept. PVC film, fitted on the inside. The film is supplied cut to your size (width × height). Manufacturer's note: if exterior panes are fully or partly covered, thermal stress can damage the glass; interior panes without sunlight or large temperature swings are not affected. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Adhesion: static cling, no adhesive Material: PVC, printed or embossed Effect: light-diffusing, no direct view through Fitting: inside Manufacturer's warranty: 5 years for indoor use

Static-cling decorative film “Star” – pattern without adhesive CDFS 6002 Star clings without adhesive and combines privacy with a decorative pattern that breaks up large glass areas. The pane stays see-through, but views in are no longer unobstructed. Fitting and later removal are quick. PVC film, fitted on the inside. The film is supplied cut to your size (width × height). Manufacturer's note: if exterior panes are fully or partly covered, thermal stress can damage the glass; interior panes without sunlight or large temperature swings are not affected. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Adhesion: static cling, no adhesive Material: PVC, printed or embossed Effect: decorative pattern, partial privacy Fitting: inside Manufacturer's warranty: 5 years for indoor use

Static-cling textured film “Arctic” with a striped look CDFS 6003 Arctic has a textured surface arranged in stripes. It diffuses light, preventing a direct view through while keeping the room bright. As it clings by static, it is applied without adhesive and can be removed quickly. PVC film, fitted on the inside. The film is supplied cut to your size (width × height). Manufacturer's note: if exterior panes are fully or partly covered, thermal stress can damage the glass; interior panes without sunlight or large temperature swings are not affected. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Adhesion: static cling, no adhesive Material: PVC, textured surface in stripes Effect: light-diffusing, no direct view through Fitting: inside Manufacturer's warranty: 5 years for indoor use

Static-cling effect film “Prisma” with a prism effect CDFS 6024 Prisma refracts incoming light like a prism, creating colourful highlights on the glass when lit. It clings by static without adhesive and is quick to put up and take down. PVC film, fitted on the inside. The film is supplied cut to your size (width × height). Manufacturer's note: if exterior panes are fully or partly covered, thermal stress can damage the glass; interior panes without sunlight or large temperature swings are not affected. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Adhesion: static cling, no adhesive Material: PVC, printed or embossed Effect: prism effect when lit Fitting: inside Manufacturer's warranty: 5 years for indoor use

Static-cling decorative film “Chapel” with a leaded-glass look CDFS 6031 Chapel resembles coloured leaded glass and also shows a prism effect when lit – an eye-catching design feature for glass doors or windows. It clings by static without adhesive and is quick to put up and remove. PVC film, fitted on the inside. The film is supplied cut to your size (width × height). Manufacturer's note: if exterior panes are fully or partly covered, thermal stress can damage the glass; interior panes without sunlight or large temperature swings are not affected. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Adhesion: static cling, no adhesive Material: PVC, printed or embossed Effect: leaded-glass look with a prism effect when lit Fitting: inside Manufacturer's warranty: 5 years for indoor use

Sandblast look in polycarbonate – privacy with little loss of light 160 Lexan is a translucent polycarbonate film with a textured surface. It strongly diffuses light and so gives privacy like satin-finished glass – according to the manufacturer with less light loss than typical sandblast-effect films. It is designed for covering whole panes, for example in washrooms, medical practices or banks. Can be fitted inside or outside. The film is supplied cut to your size (width × height); roll width: 137 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Material: translucent polycarbonate film, 75 µm, textured surface Adhesive: acrylic Temperature resistance when applied: -30 °C to +95 °C Application temperature: at least +12 °C Fitting: inside and outside Manufacturer's warranty: 7 years indoors; outdoors 2 years when fitted vertically, 1 year when inclined

Satin-glass look for privacy in bathrooms, practices or offices Clear Frost makes glass look satin-finished: the textured surface diffuses the light so that a clear view through is prevented while the room stays bright. Typical places are washrooms, medical practices or banks. Unlike satin-finished glass, the film can be retrofitted and removed again. Translucent polyester film, fitted on the inside. The film is supplied cut to your size (width × height); roll widths: 183 and 152 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Visible light transmission (VLT): 65 % on 4 mm single glazing, 60 % on 4/12/4 mm double glazing Visible light reflection outside/inside: 25/27 % on 4 mm single glazing g-value (total solar energy transmittance): 0.65 on 4 mm single glazing, 0.63 on 4/12/4 mm double glazing Total solar energy rejected (90°): 35 % on 4 mm single glazing, 37 % on 4/12/4 mm double glazing UV protection (300–380 nm): over 99 %; fading protection 47 % on 4 mm single glazing Thickness: 50 µm; fire classification B/s1/d0 to EN 13501-1 Manufacturer's warranty: 7 years for indoor use

Bright frosted look with an “iced” finish – full adhesive Iced Haze gives glass a sandblasted look in a subtle, neutral tone without glitter. According to the data sheet it lets through approx. 82 % of the light, so it provides privacy without noticeably darkening the room. This version has a conventional full-surface adhesive. The PVC film is suitable for whole panes, digital printing or plotter cutting and can be fitted inside or outside. The film is supplied cut to your size (width × height); roll width: 160 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Light transmission: approx. 82 % Material: translucent PVC film, approx. 80 µm Adhesive: full-surface, permanent (acrylic) Application temperature: at least +8 °C Printable: UV, latex, (eco-)solvent Manufacturer's warranty: 10 years indoors, 3 years outdoors when fitted vertically (based on a Central European climate)

Bright frosted look – with air channels for dry application Iced Haze+ is the version of Iced Haze with an air-channel adhesive: air escapes as you press the film down, so it can be applied dry, quickly and without bubbles – it is intended for dry application only. Look and light transmission (approx. 82 %) are the same as Iced Haze: neutral, “iced” privacy without glitter, for inside or outside use. The film is supplied cut to your size (width × height); roll width: 160 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Light transmission: approx. 82 % Material: translucent PVC film, approx. 80 µm Adhesive: acrylic with air channels – dry application only Application temperature: at least +8 °C Printable: UV, latex, (eco-)solvent Manufacturer's warranty: 10 years indoors, 3 years outdoors when fitted vertically (based on a Central European climate)

Sandblast-look privacy film with a silvery pearl shimmer Pearly Haze combines a sandblasted look with fine silvery flakes. It provides very good privacy and, according to the data sheet, still lets through approx. 55 % of the light. This version has a conventional full-surface adhesive. The PVC film is suitable for whole panes, digital printing or plotter cutting and can be fitted inside or outside. The film is supplied cut to your size (width × height); roll width: 160 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Light transmission: approx. 55 % Material: translucent PVC film, approx. 75 µm Adhesive: full-surface, permanent (acrylic) Application temperature: at least +8 °C Printable: UV, latex, (eco-)solvent Manufacturer's warranty: 10 years indoors, 3 years outdoors when fitted vertically (based on a Central European climate)

Pearl-shimmer privacy film – with air channels for dry application Pearly Haze+ is the version of Pearly Haze with an air-channel adhesive for quick, bubble-free fitting – for dry application only. Look and light transmission (approx. 55 %) are the same as Pearly Haze: sandblasted look with silvery flakes, good privacy, for inside or outside use. The film is supplied cut to your size (width × height); roll width: 160 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Light transmission: approx. 55 % Material: translucent PVC film, approx. 75 µm Adhesive: acrylic with air channels – dry application only Application temperature: at least +8 °C Printable: UV, latex, (eco-)solvent Manufacturer's warranty: 10 years indoors, 3 years outdoors when fitted vertically (based on a Central European climate)

Low-E film for summer and winter – with more solar control XE 50 combines solar control in summer with a low-E effect in winter: its coating returns part of the room's heat to the room. Compared with XE 70 it is darker and blocks more solar heat. Note from the data sheet: under artificial light an iridescent effect (“oil film”) may be visible on the glass. It is fitted on the inside. The film is supplied cut to your size (width × height); roll width: 152 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Visible light transmission (VLT): 51 % on 4 mm single glazing, 47 % on 4/12/4 mm double glazing g-value (total solar energy transmittance): 0.42 on 4 mm single glazing, 0.49 on 4/12/4 mm double glazing Total solar energy rejected (90°): 58 % on 4 mm single glazing, 51 % on 4/12/4 mm double glazing Low-E: emissivity 0.37; Ug-value 4.4 W/(m² °C) on 4 mm single glazing, 2.4 W/(m² °C) on 4/12/4 mm double glazing UV protection (300–380 nm): over 99 %; fading protection 54 % on 4 mm single glazing Thickness: 50 µm; fire classification B/s1/d0 to EN 13501-1 Manufacturer's warranty: 15 years

All-year film: less heat in summer, less heat loss in winter XE 70 is a low-E film for the room side. In summer it reduces incoming solar heat; in winter its coating reflects part of the room's heat back and so lowers heat loss through the glass. It is very light and shows little reflection on the inside. It is a multi-layer polyester film with a scratch-resistant surface. The film is supplied cut to your size (width × height); roll width: 148 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Visible light transmission (VLT): 68 % on 4 mm single glazing, 62 % on 4/12/4 mm double glazing g-value (total solar energy transmittance): 0.49 on 4 mm single glazing, 0.52 on 4/12/4 mm double glazing Total solar energy rejected (90°): 51 % on 4 mm single glazing, 48 % on 4/12/4 mm double glazing Low-E: emissivity 0.09; Ug-value 3.4 W/(m² °C) on 4 mm single glazing, 2.1 W/(m² °C) on 4/12/4 mm double glazing UV protection (300–380 nm): over 99 %; fading protection 52 % on 4 mm single glazing Thickness: 75 µm; fire classification B/s1/d0 to EN 13501-1 Manufacturer's warranty: 15 years

Opaque white film: blocks the view and reduces glare Film 150 is a white, opaque polyester film. It blocks the view, reduces glare and clearly cuts solar heat – useful for glass partitions, industrial halls or hospitals. It is fitted on the inside. The film is supplied cut to your size (width × height); roll width: 152 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Visible light transmission (VLT): 9 % on 4 mm single glazing, 9 % on 4/12/4 mm double glazing Visible light reflection outside/inside: 70/84 % on 4 mm single glazing g-value (total solar energy transmittance): 0.21 on 4 mm single glazing, 0.29 on 4/12/4 mm double glazing Total solar energy rejected (90°): 79 % on 4 mm single glazing, 71 % on 4/12/4 mm double glazing UV protection (300–380 nm): over 99 %; fading protection 92 % on 4 mm single glazing Thickness: 50 µm; fire classification B/s1/d0 to EN 13501-1 Manufacturer's warranty: 7 years for indoor use

Opaque black film for complete blackout Film 170 is a black, opaque polyester film. According to the data sheet it lets no visible light through, making it suitable for complete blackout and for protecting very light-sensitive goods or equipment. At the same time it clearly reduces solar heat. It is fitted on the inside. The film is supplied cut to your size (width × height); roll width: 152 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Visible light transmission (VLT): 0 % on 4 mm single glazing, 0 % on 4/12/4 mm double glazing Visible light reflection outside/inside: 6/7 % on 4 mm single glazing g-value (total solar energy transmittance): 0.23 on 4 mm single glazing, 0.51 on 4/12/4 mm double glazing Total solar energy rejected (90°): 77 % on 4 mm single glazing, 49 % on 4/12/4 mm double glazing UV protection (300–380 nm): over 99 %; fading protection 100 % on 4 mm single glazing Thickness: 75 µm; fire classification B/s1/d0 to EN 13501-1 Manufacturer's warranty: 7 years for indoor use

Removable protective film against scratches and graffiti – 200 µm Film 701 is a crystal-clear, heavy-duty protective film for glass in exposed places – shop windows, bus shelters or public transport vehicles. If it gets scratched or sprayed, it can be peeled off and replaced instead of replacing the pane. It can be fitted inside or outside. The film is supplied cut to your size (width × height); roll widths: 183, 152 and 122 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Visible light transmission (VLT): 88 % on 4 mm single glazing UV protection (300–380 nm): over 98 %; fading protection 25 % on 4 mm single glazing Thickness incl. adhesive: 200 µm; fire classification B/s1/d0 to EN 13501-1 Manufacturer's warranty: 5 years indoors; outdoors 2 years when fitted vertically, 1 year when inclined

Thinner removable protective film against scratches and graffiti – 125 µm Film 702 is a crystal-clear protective film, 125 µm thick, that guards glass in exposed places against scratches and graffiti. If it is damaged, it is peeled off and renewed – the pane itself is spared. Can be fitted inside or outside. The film is supplied cut to your size (width × height); roll widths: 183, 152 and 122 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Visible light transmission (VLT): 88 % on 4 mm single glazing UV protection (300–380 nm): over 99 % Thickness incl. adhesive: 125 µm; fire classification B/s1/d0 to EN 13501-1 Manufacturer's warranty: 5 years indoors; outdoors 2 years when fitted vertically, 1 year when inclined