Advice +49 9732 3023858 · Mon–Thu 9 am–4 pm, Fri 9 am–2 pm shop@sonnenschutzshop24.eu Free shipping within Germany (except islands/freight) Shop rating: 4,83 out of 5 · 282 reviews on ProvenExpert
Go to homepage
Send a message
€0.00

Made-to-measure sun protection

SMART H55 roller door with fall arrest device made to measure

Shop rating: 4,83 out of 5 · 282 reviews on ProvenExpert
  • Width up to 400 cm, height up to 385 cm
from €1,047.87
incl. VAT · free shipping within Germany (except islands)
Delivery time 2 weeks
Configure now Advice +49 9732 3023858
Free shipping within Germany (except islands)
Payment by prepayment (bank transfer)
24 months statutory warranty
Expert advice Mon–Fri · +49 9732 3023858

Configurator

SMART H55 roller door with fall arrest device in 3 steps

Choose step by step. The price updates with every change, and you can change completed steps at any time.

cm
Info and measuring guide

Please state in cm.

Measuring help for roller doors

Our finished dimensions are outer edge dimensions.

Depending on the installation type, the rail widths as well as the box height and bottom rail must be added.

Example door ROLLUX SMART H55:

Installation type 1 = in the opening

- Your clear dimensions (garage opening dimensions) are e.g. 280 cm wide by 210 cm high = order dimensions 279.5 cm wide by 209.5 cm high.

You want to install in the opening (type 1).

The passage dimensions are reduced by the two guide rail widths (2 x 8.5 cm)

This leaves a passage width of 263 cm.

The passage height is reduced by the box height of 21 cm and the bottom rail of 8 cm,

which does not roll into the box.

This leaves a passage height of 210 cm - 21 cm - 8 cm (with OSE - 10 cm) = 181 cm.

--------------------------------------------------------------------------------

Installation type 2 or 3 = behind or in front of the opening

It is therefore advisable to install behind the reveal opening (type 2) or in front of it (type 3)

in order to retain the passage dimensions of the garage opening.

The measurement for type 2 or type 3 is the same.

Add the box dimension of 21 cm + 8 cm bottom rail

(with OSE + 10 cm) to your clear opening height.

The order height would therefore be 210 cm + 21 cm + 8 cm (with OSE + 10 cm) = 239 cm.

Please add 2 x rail dimension = 17 cm to your clear passage width.

The order width would therefore be 297 cm.

cm
Info and measuring guide

Please state in cm.

Measuring guide for roller doors

Our finished dimensions are outer edge dimensions.

Depending on the type of installation, the rail widths as well as box heights and bottom rails must be added.

Example door SMART H55:

Installation type 1 = in the opening

- Your clear dimensions (garage opening dimensions) are e.g. 280 cm wide by 210 cm high = order dimensions 279 cm wide by 209 cm high.

You want to install in the opening (type 1).

The passage dimensions are reduced by the two guide rail widths (2 x 8.5 cm)

This leaves a passage width of 263 cm.

The passage height is reduced by the box height of 23 cm and the bottom rail of 8 cm,

which does not roll into the box.

This leaves a passage height of 210 cm - 23 cm - 8 cm (with OSE - 10 cm) = 179 cm.

--------------------------------------------------------------------------------

Installation type 2 or 3 = behind or in front of the opening

It is therefore advisable to install behind the reveal opening (type 2) or in front of it (type 3)

in order to retain the passage dimensions of the garage opening.

The measuring for type 1 or type 3 is the same.

Add the box dimension of 23 cm + 8 cm bottom rail

(with OSE + 10 cm) to your clear opening height.

The order height would therefore be 210 cm + 23 cm + 8 cm (with OSE + 10 cm) = 241 cm.

Please add 2 x rail dimension = 17 cm to your clear passage width.

The order width would therefore be 297 cm.

How to measure

Measuring guide for option 1: Fitting directly into the reveal opening. The convex side of the curtain faces outwards. The box faces inwards. Please measure the clear width at the top, bottom and middle. Deduct 0.5–1 cm from the smallest measurement. This is the finished width (order width).

The finished height is the clear height from the top of the reveal (where the box will sit) to the floor minus 0.5–1 cm (order height).


Option 2: Fitting behind the reveal opening (if there is space). Measure as follows: add 17 cm (2 x rail width of 85 mm per side) to the width of the reveal opening. Order height = top edge of box to bottom edge of bottom rail. The advantage of this fitting method is that the clear passage height does not change (if there is space above the reveal opening). The convex side of the curtain faces outwards. The box faces inwards, see original picture.


Option 3: Fitting in front of the reveal opening (as option 2, but the box faces outwards. The convex side of the curtain faces inwards. Please state "Type 3" when ordering.

Phone: +49 9732 3023858 · Mon–Thu 9 am–4 pm, Fri 9 am–2 pm

Motor type
Info and measuring guide

We supply drives and controls from the German manufacturers BECKER® and RADEMACHER® (depending on stock availability). Drive side always as seen from inside.

Motor type Motor type Motor type Motor type

Internal emergency crank gear incl. 150 cm hand crank

(the type of fitting is adapted to the installation method)

Motor type

Always state the motor side as seen from inside, regardless of which installation method you use. We only install BECKER® motors.

The BECKER® radio control is supplied with a 2-channel hand transmitter.

If you need more hand transmitters, please select them under Extras.

Box colour

The colour dots show an approximate shade – screen colours may differ from the original.

Info and measuring guide

Standard box and rail colour available in white - grey - brown - silver

or to RAL = plus 20% surcharge (4 weeks delivery time)

Shutter curtain colour

The colour dots show an approximate shade – screen colours may differ from the original.

Info and measuring guide

You can order the aluminium roller door curtain in the following colours at no surcharge:

Shutter curtain colour
Fitting type
Info and measuring guide

Measuring instructions for type 1: Please measure the clear width at the top, bottom and in the middle.

Deduct 0.5 cm from the smallest dimension. This is the finished width.

The finished height is the clear height from the top edge of the reveal (where the box will eventually be) to the floor.

Variant 1: installation directly in the reveal opening, measuring as described above.

Fitting type

Variant 2: installation behind the reveal opening (if there is space), measuring as follows: please add 17 cm (2 x rail dimension) to the width of the reveal opening.

Order height = top edge of box to bottom edge of guide rail. The advantage of this type of installation is that the passage height does not change. (if there is space above the reveal opening)

Fitting type

Variant 3: installation in front of the reveal opening (as variant 2, only the box faces outwards): please state "Type 3" when ordering.

OSE bottom rail
Info and measuring guide

- In accordance with current EU regulations, roller doors operated by radio remote control must be fitted with a so-called OSE safety edge with electronics (optical sensor bottom rail).

This regulation applies to doors in public places as well as to doors on commercial premises etc.

However, an OSE bottom rail with electronics only makes sense with radio remote control. In all other cases, such as switches or key switches, the person operating the switch is responsible for moving the door.

The old rule under which so-called DW bottom rails (pressure wave rails) were also permitted is no longer valid.

These considerably cheaper bottom rails are still frequently offered by competitors.

- As a retrofit safety extra for roller doors without OSE electronics, we recommend installing a light barrier on radio-operated doors. This serves a similar purpose: if the roller door is lowered unattended by radio while there are obstacles, animals or children underneath, the roller door stops and does not roll down any further.

The difference from the OSE safety edge with electronics is that in an emergency the door does not automatically reverse (as is the case with OSE electronics), but merely stops.

What private individuals ultimately install on their own property is up to them.

A 4 cm high OSE rubber seal with rain drainage profile in an extruded aluminium profile is standard.

Optionally with OSE electronics to DIN, in conjunction with a radio control. If no OSE rubber seal is required, we supply an ECO finish with a 1 cm hard rubber profile in the last slat at a 3% discount.

OSE bottom rail
Emergency crank gear
Info and measuring guide

In the event of a power failure, the door can still be operated by crank. An additional gear unit is fitted on the shaft.

With installation type 3, in front of the opening, the crank entry on the box is closed with a rubber plug so that unauthorised opening is not possible. In an emergency, the rubber plug must then be removed and the crank can be inserted from outside to operate the door manually.

Crank operation can be chosen freely, from outside or from inside. We manufacture according to your requirements.

Emergency crank gear

Please note: image for illustration purposes only. Deviations possible.

Extras
Info and measuring guide

- required if you want to install a door without safety extras such as a light barrier or OSE edge, but with 2 switches (push button inside, e.g. key switch outside)

This isolating relay is a flush-mounted version and only needs to be connected in between if the switches are wired for SELF-HOLDING (switch function latches permanently), in order to avoid short circuits. You can avoid this type of connection by installing the switches not with self-holding but only with a push-button/dead-man function.

Our switches are supplied with a push-button/dead-man function and can be switched over.

Explanation of dead-man control:

The operator keeps the switch pressed until the door has been raised or lowered.

Explanation of the self-holding function:

The operator presses the switch once and the motor runs through to the respective end position.

In conjunction with a BECKOTRONIC 5 radio roller door control and an additional switch, no separate isolating relay is needed, because the control itself takes care of this. An additional switch connection is provided on the control.

If you select "wired code keypad", NO isolating relay is required when connecting an additional switch.

Info and measuring guide

If you would like a code keypad for outside, this is only possible by means of a radio control.

In this case you will receive a radio-operated code keypad on which you can set any number combination. The advantage of this combination is that you do not necessarily need a "misplaced" hand-held transmitter to open the door system. Any user who enters the preset number combination can open the door from outside.

As the commands are transmitted from the code keypad to the control exclusively by radio, there is also no need for complex wiring.

There is also a manual switch on the control itself. An additional switch for inside is therefore not necessary.

When using a normal switch and a key switch, please note when connecting that a multi-point isolating relay must be connected in between. If no relay is used, there is a risk of damage to the roller door motor. Your authorised electrician should advise you on this. For an explanation and ordering option, see the selection field EXTRAS.

AP = surface-mounted

UP = flush-mounted

Based on our many years of experience, in addition to the normal commercial packaging supplied as standard, we now also offer optional double extra-secure packaging. This is made with 2 cm thick wooden slats all round, so that the door is delivered in a closed "wooden crate".

Our normal free packaging is of course also secure and approved by the carrier. Any damage caused by the carrier during loading at the regional transit stop is always insured.

With both types of packaging, if there is transport damage on delivery, please proceed exactly as described in our delivery information, which you will receive during the rest of the ordering process.

With the additional packaging option offered here, we have responded to customer requests to make delivery even more worry-free, as a thorough inspection of the packaging is then practically no longer necessary. If you have any questions about this, we will be happy to help.

- this is generally only required if the door is used commercially and is regularly inspected by official inspection bodies

- the so-called inspection book is not actually a book but just individual sheets on which numerous details about the door are recorded, such as serial number, motor number, anti-fall device number, tensile force test, manufacturer etc.

Call-back service
Please complete all steps first.

Product description

Buy the H55 roller door with fall arrest device from system supplier Heroal here.

PREMIUM specification. For electric roller doors, the order sizes are calculated from the outside-edge width and outside-edge height. For maximum safety, always supplied with a fall arrest device.

(The illustration shows fitting option 2 = behind the opening, box facing inwards. The rear box cover and guide rails are not visible from outside; the convex side of the curtain faces outwards.)

As standard, our roller doors are fitted with a robust, high-quality integrated mechanical 230 V BECKER® / RADEMACHER® tubular motor (depending on stock availability) including a fall arrest device, and can optionally be operated by BECK-O-TRONIC® radio control or by a switch only. Other circuits, such as yard lighting, can also be connected to the BECK-O-TRONIC®.


Our doors use Heroal® aluminium profiles. As standard, the SMART H55 has a 4 cm rubber seal on the aluminium bottom rail.

For roller doors weighing over 20 kg, a fall arrest device is not an option but a requirement.

The foam-filled aluminium curtain (face = 52 mm high x 13.5 mm thick to DIN) is fitted like a conventional roller shutter in, behind or in front of the reveal opening. These doors are supplied fully pre-assembled with the curtain rolled up. Fixing screws into the building structure are not included in the scope of delivery.

We are happy to send you fitting notes for this roller door on request.

The 23 / 25 or 30 cm high box (bevelled at 45 degrees at the front) has a clean shape and suits any façade. The keder-guided rails measure 28 mm deep and 85 mm wide and allow the curtain to run almost silently.

Box heights:

- up to 300 cm door width x 250 cm door height = 23 x 23 box size

- up to 300 cm overall door height = 25 x 25 cm box size, above that 30 x 30 cm

Roller door order sizes: drive side always viewed from inside.

Top edge of box to bottom edge of bottom rail = order height

Outer edge of rail to outer edge of rail = order width

Steel springs suspending the curtain inside the box on a sturdy 60/70 or 125 mm steel shaft differ from conventional roller shutter shafts in their greater stability and durability.

As standard, the aluminium bottom slat of the door has a 4 cm thick rubber lip with a rain drainage profile in the extruded aluminium section (see picture on the left), which compensates very well for uneven floors. To prevent the rubber seal from being completely crushed when the door closes and breaking after a while, as happens with inferior designs, we fit special stop blocks at the bottom of the side guide rails that stop the rubber from being squashed and damaged. With the OSE safety edge option with electronics, the same aluminium bottom rail system is used. The only difference is that in this case it contains the sensors for the OSE control. If no OSE rubber seal is required, we supply an ECO seal with a 1 cm rubber profile in the last slat at a reduction of EUR 29.


Our view: High-quality German Heroal® branded product and a cost-effective option for small garage doors that are easy to install yourself. Can be made in any width from 160 cm to 400 cm and up to 320 cm high. (*Special heights up to 370 cm can be made; in the configurator these can be ordered up to a width of 320 cm)

Box and rail colour available in white - grey - brown - silver or in a RAL colour = plus 20% surcharge

Aluminium slat dimensions:


Fitting options: These roller doors can be fitted in different ways.

Summary of winding direction:

- if the box faces outwards (left roller), the convex side of the curtain always faces inwards

- if the box faces inwards (right roller), the convex side of the curtain always faces

outwards. All available accessories, such as radio controls, switches, keypads, emergency crank option etc., can be found in the configuration.

Important note on the condition of the garage:

- the garage must be closed on all sides once the door is installed (if the garage is open at the back, the increased wind load can push the curtain backwards out of the guide rails) - when fitting 2 doors to one opening, we recommend the RD75 door system with the curtain interlocked inside the guide rails

We deliver in secure packaging with 2 cm thick timber all round and a viewing window so you can inspect the goods on delivery.


***Restriction: These doors are not suitable as high-speed doors or for minute-by-minute operating cycles (supermarket, loading bay etc.). Every tubular motor has a thermal switch and shuts the system down in the event of overload / overheating.

Order your high-quality motorised garage roller door with aluminium slats here in the roller door configurator up to 400 cm wide.

Delivery to Switzerland, Austria and selected EU countries is possible.



Technology & fitting

Key data from the configurator

Sizes
Width up to 400 cm · height up to 385 cm
Delivery time
2 weeks

Instructions & downloads

Advice

Personal expert advice

Not sure about size, fabric or fitting? Call us or let us check your configuration before production.

+49 9732 3023858

Mon–Thu 9 am–4 pm, Fri 9 am–2 pm

Have my configuration checked

What customers say

4,83
Shop rating: 4,83 out of 5 · 282 reviews on ProvenExpert

Overall rating of our shop on ProvenExpert. As of 18.10.2026

All reviews on ProvenExpert

Reviews of this product

SMART H55 roller door with fall arrest device
This website uses cookies to ensure the best experience possible. More information...