Roller door HRT05 without fall arrest device made to measure

We supply drives and controls from the German manufacturer elero®

Drive side always as seen from inside. All elero motors have electronic torque cut-off. Control by Becker®

Always state the motor side as seen from inside, regardless of which installation method you use. We only install BECKER® motors for a 230 V connection.

The BECKER® radio control is supplied with a 2-channel hand transmitter.

If you need more hand transmitters, please select them under Extras.

If you select the 12 V motor and radio solar module, the set is supplied as follows:

- 12 V, 20 Nm motor installed in the roller door

- 1 x solar panel

- 1 x control unit with Li-ion battery pack, incl. charger for external charging

- 1 x hand transmitter

- 1 x wall bracket for the control unit

You can order the aluminium roller door curtain in the following colours at no surcharge:

Extruded type = with considerably higher material rigidity, available for a surcharge.

Measuring instructions for type 1: Please measure the clear width at the top, at the bottom and in the middle.

Deduct 0.5 cm from the smallest dimension. This is the finished width.

Variant 1: Mounting directly in the reveal opening, measure as described above.

Variant 2: Mounting behind the reveal opening (if space is available), measure as follows: Please add 14 cm (2 x rail width) to the width of the reveal opening.

Order height = top edge of box to bottom edge of guide rail. The advantage of this mounting type is that the clearance height does not change. (if space is available above the reveal opening)

Variant 3: Mounting in front of the reveal opening (as variant 2, but with the box facing outwards): Please specify "Type 3" when ordering.

Different sizes and equipment are available on request.

The dimensions refer to the clear dimensions.

For example: clear width 250 cm + 2 x guide rail dimension 6.8 cm (13.6 cm) = overall width 263.6 cm.

Or 250 cm clear height + 21 cm box = overall height 271 cm.

In the event of a power failure, the door can still be operated by crank. An extra gear is fitted on the shaft.

With the emergency crank motor option, we always supply a removable crank.

Crank operation can be chosen freely, from outside or from inside. We manufacture to your requirements.

- In accordance with current EU regulations, roller doors operated by radio remote control must be fitted with a so-called OSE safety edge (optical sensor bottom rail).

This regulation applies to doors in public places just as it does to doors on commercial premises etc.

However, an OSE bottom rail only makes sense with radio remote control. In all other cases, such as a switch or key switch, it is the responsibility of the person operating the switch to move the door.

The old rule, under which so-called DW bottom rails (pressure-wave rails) were also permitted, is no longer valid.

Many competitors still offer these considerably cheaper bottom rails.

- as a retrofit safety extra for roller doors without OSE,

we recommend installing a light barrier on radio-operated doors.

This serves a similar purpose: if the roller door is lowered by radio while unattended and there are obstacles, animals or children underneath, the roller door stops and does not continue to unroll.

The difference from the OSE safety edge is that in an emergency the door does not automatically reverse (as is the case with OSE), but simply stops.

What private individuals ultimately install on their own property is up to them.

Please note:

If you configure a motor with radio control and select the OSE safety edge with OSE electronics, you will also receive an original Beckotronic 5 roller door control unit with evaluation.

4 cm high OSE rubber seal with rain drainage profile in combination with OSE electronics and radio control. Or optionally without OSE electronics, as a bottom rail seal. The standard bottom rail seal is a 1 cm hard rubber lip.

If you would like a code keypad for outside, this is only possible by means of a radio control.

In this case you will receive a radio-operated code keypad on which you can set any number combination. The advantage of this combination is that you do not necessarily need a "misplaced" hand-held transmitter to open the door system. Any user who enters the preset number combination can open the door from outside.

As the commands are transmitted from the code keypad to the control exclusively by radio, there is also no need for complex wiring.

There is also a manual switch on the control itself. An additional switch for inside is therefore not necessary.

When using a normal switch and a key switch, please note when connecting that a multi-point isolating relay must be connected in between. If no relay is used, there is a risk of damage to the roller door motor. Your authorised electrician should advise you on this. For an explanation and ordering option, see the selection field EXTRAS.

AP = surface-mounted

UP = flush-mounted

- this is generally only required if the door is used commercially and is regularly inspected by official inspection bodies

- the so-called inspection book is not actually a book but just individual sheets on which numerous details about the door are recorded, such as serial number, motor number, anti-fall device number, tensile force test, manufacturer etc.