Made-to-measure frosted window film

Sandblast look in polycarbonate – privacy with little loss of light 160 Lexan is a translucent polycarbonate film with a textured surface. It strongly diffuses light and so gives privacy like satin-finished glass – according to the manufacturer with less light loss than typical sandblast-effect films. It is designed for covering whole panes, for example in washrooms, medical practices or banks. Can be fitted inside or outside. The film is supplied cut to your size (width × height); roll width: 137 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Material: translucent polycarbonate film, 75 µm, textured surface Adhesive: acrylic Temperature resistance when applied: -30 °C to +95 °C Application temperature: at least +12 °C Fitting: inside and outside Manufacturer's warranty: 7 years indoors; outdoors 2 years when fitted vertically, 1 year when inclined

Satin-glass look for privacy in bathrooms, practices or offices Clear Frost makes glass look satin-finished: the textured surface diffuses the light so that a clear view through is prevented while the room stays bright. Typical places are washrooms, medical practices or banks. Unlike satin-finished glass, the film can be retrofitted and removed again. Translucent polyester film, fitted on the inside. The film is supplied cut to your size (width × height); roll widths: 183 and 152 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Visible light transmission (VLT): 65 % on 4 mm single glazing, 60 % on 4/12/4 mm double glazing Visible light reflection outside/inside: 25/27 % on 4 mm single glazing g-value (total solar energy transmittance): 0.65 on 4 mm single glazing, 0.63 on 4/12/4 mm double glazing Total solar energy rejected (90°): 35 % on 4 mm single glazing, 37 % on 4/12/4 mm double glazing UV protection (300–380 nm): over 99 %; fading protection 47 % on 4 mm single glazing Thickness: 50 µm; fire classification B/s1/d0 to EN 13501-1 Manufacturer's warranty: 7 years for indoor use

Bright frosted look with an “iced” finish – full adhesive Iced Haze gives glass a sandblasted look in a subtle, neutral tone without glitter. According to the data sheet it lets through approx. 82 % of the light, so it provides privacy without noticeably darkening the room. This version has a conventional full-surface adhesive. The PVC film is suitable for whole panes, digital printing or plotter cutting and can be fitted inside or outside. The film is supplied cut to your size (width × height); roll width: 160 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Light transmission: approx. 82 % Material: translucent PVC film, approx. 80 µm Adhesive: full-surface, permanent (acrylic) Application temperature: at least +8 °C Printable: UV, latex, (eco-)solvent Manufacturer's warranty: 10 years indoors, 3 years outdoors when fitted vertically (based on a Central European climate)

Bright frosted look – with air channels for dry application Iced Haze+ is the version of Iced Haze with an air-channel adhesive: air escapes as you press the film down, so it can be applied dry, quickly and without bubbles – it is intended for dry application only. Look and light transmission (approx. 82 %) are the same as Iced Haze: neutral, “iced” privacy without glitter, for inside or outside use. The film is supplied cut to your size (width × height); roll width: 160 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Light transmission: approx. 82 % Material: translucent PVC film, approx. 80 µm Adhesive: acrylic with air channels – dry application only Application temperature: at least +8 °C Printable: UV, latex, (eco-)solvent Manufacturer's warranty: 10 years indoors, 3 years outdoors when fitted vertically (based on a Central European climate)

Sandblast-look privacy film with a silvery pearl shimmer Pearly Haze combines a sandblasted look with fine silvery flakes. It provides very good privacy and, according to the data sheet, still lets through approx. 55 % of the light. This version has a conventional full-surface adhesive. The PVC film is suitable for whole panes, digital printing or plotter cutting and can be fitted inside or outside. The film is supplied cut to your size (width × height); roll width: 160 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Light transmission: approx. 55 % Material: translucent PVC film, approx. 75 µm Adhesive: full-surface, permanent (acrylic) Application temperature: at least +8 °C Printable: UV, latex, (eco-)solvent Manufacturer's warranty: 10 years indoors, 3 years outdoors when fitted vertically (based on a Central European climate)

Pearl-shimmer privacy film – with air channels for dry application Pearly Haze+ is the version of Pearly Haze with an air-channel adhesive for quick, bubble-free fitting – for dry application only. Look and light transmission (approx. 55 %) are the same as Pearly Haze: sandblasted look with silvery flakes, good privacy, for inside or outside use. The film is supplied cut to your size (width × height); roll width: 160 cm. Before you order, please check that the film suits your glazing – the guide and the data sheet below explain what to look for. Light transmission: approx. 55 % Material: translucent PVC film, approx. 75 µm Adhesive: acrylic with air channels – dry application only Application temperature: at least +8 °C Printable: UV, latex, (eco-)solvent Manufacturer's warranty: 10 years indoors, 3 years outdoors when fitted vertically (based on a Central European climate)