Reflexa

Buy an electric carport roller shutter or small roller door up to 400 cm wide for retrofitting in our configurator. Can be used as a carport roller door with a curtain weight of up to 20 kg. Available as Creato (round box) or Conturo (bevelled box). System supplier HEROAL®, made up by Reflexa®. Elero® motors with electronic limit switching as standard. Aluminium profile as standard. Wide choice of colours. Tested and certified roller shutters. You can use these roller shutters for indoor or outdoor fitting – also for patio doors and large window fronts. Advantages and features at a glance: - German Elero® RolTop D+ motors (electronic limit setting), no need to set the end positions - alternatively equivalent Somfy motors, depending on stock availability - also available with battery solar drive (including radio remote control and solar panel) - also available with crank drive (with removable crank) - made in Germany - hail impact tested, foam-filled aluminium curtain 52 mm high x 13.5 mm to DIN (MAXI profile) - Energy Label - larger possible sizes (up to 400 cm wide at 220 cm height, or 220 cm wide and 350 cm high) - integrated anti-lift protection through fixed shaft connectors - extruded bottom rails with rubber seal - 5-sided Conturo R box (bevelled at the front) or Creato R half-round box at no extra charge - sturdy CL 53 guide rails = 53 mm wide x 22 mm deep (piping insert for noise reduction) - optionally CL 68 rail type at no extra charge = 68 mm wide x 26.5 mm deep (greater curtain insertion depth) - box roll-formed as standard, extruded on request - box height always 20.5 cm - 60 mm octagonal steel shaft with bearing-mounted aluminium end cap - all RAL box and rail colours can be ordered at no extra charge - up to 265 cm wide x 273 cm high also usable as a roller door, as the curtain weight is below 20 kg - no fixings for the building structure are included in the delivery According to Reflexa, its roller shutters are made in Germany. The HEROAL® HSM 52 aluminium profile is filled with high-quality foam and has a face of 52 mm x 13.5 mm (measured without locking) The following curtain colours are available: This product is made to measure to your specifications and cannot be returned or exchanged. The order sizes are always the overall dimensions. Outer edge of guide rail to outer edge of guide rail = order width Top edge of box to bottom edge of bottom rail = order height The guide rails are 53 mm or 68 mm wide per side. The box height is always 20.5 cm

Every Reflexa® combination roller shutter comes with motor drive and is technically identical to the AsyRoll sloping roller shutter. Order online from us, made to measure. Colours, box shapes and slats are matched exactly to the main roller shutter. It is therefore available with a square or round box and a curtain with light slots. It is measured like a single roller shutter. Outer edge of guide rail to outer edge of guide rail = order width When combined with the sloping unit, the two guide rails are fitted back to back. Top edge of box to bottom edge of bottom rail = order height. You can order the sloping roller shutter here: Sloping roller shutter AsyRoll Comfort

Reflexa® F 2.8 fly screen frame with spring pins in a high-quality version. Made to measure and delivered ready to fit. Fitted between the roller shutter and the window frame. Configure and buy in our shop. High-quality workmanship on all aluminium profiles, extruded profiles. No plastic inserts, but high-quality aluminium connectors. Quality fibreglass mesh in grey or black, or special mesh as an option: stainless steel or with pollen protection, matching our Reflexa® insect screen doors and roller screens. Any RAL profile colour possible at no extra charge. If you need a straight finish on the inner contact surface of the fixed frame, or if fitting between the roller shutter rails is essential, choose this F 2.8 fixed frame. The fixed frames are simply clamped into the timber or PVC frame using special spring pins (holes in the frame are required). The fixed frames are ready to fit. Fully assembled fixed frame, viewed from outside. Space required: 9 mm depth. Brush seal all round on the outer edge of the frame. Fitting options: in front of the window frame; between the roller shutter rails. The profile thickness of the insect screen frame is 8 mm. Installation depth 9 mm. A centre bar is fitted for heights / widths over 120 cm.

Reflexa® E 2.8 insect screen fixed frame in a high-quality design. Made to measure and delivered ready to fit. Configure and order in our shop. The aluminium profiles are mitred at the corners. No plastic inserts, but high-quality aluminium corner connectors. The equally high-quality, rot-proof fibreglass mesh is available in black, grey, stainless steel or with pollen protection, to match our Reflexa® insect screen doors and roller screens. If you need a flush finish on the inside where the frame rests, choose the E 4 fixed frame from our range. The frames are simply clamped into the sash using special turn clips. For different sash thicknesses, we supply different-sized brackets of your choice at no extra cost. Fully fitted fixed frame, viewed from outside. These fixed frames cannot be used where roller shutter rails are fitted directly in front. Space required: 9 mm depth. Fitting options: in front of the window frame. The insect screen frame profile is 8 mm thick. Installation depth 9 mm. A centre bar is fitted above 120 cm height / width.

You can order interior venetian blinds with 35 mm or 50 mm slats for shading large widths online from us. Use our venetian blind configurator. Delivery to Switzerland and Austria is also available. Features: Head and bottom rails only available in white or silver. With Reflexa, any colour can be chosen free of charge. Ladder cords to match the slat colour; tapes available in white, silver or black Standard wall/ceiling brackets are included. Head rail used: Cord and crank operation with 35 / 50 mm aluminium slats = head rail 40 x 40 mm. Same 40 mm x 40 mm high head rail with continuous cord and 50 mm slats. With motor drive generally = head rail 57 mm x 51 mm. Maximum width 380 cm x 280 cm height.

With lateral zip fabric guide using a zip system for optimum fabric tension. The fabric is tensioned on all sides. Single units can be made up to 600 cm wide with a 500 cm projection. Configure the Reflexa® LifeSmall Zip in our shop and order online. Also available with a Variovolant on request. Another option for shading a glass roof from below is the more economical standard under-roof awning. Key features: - electric motor as standard (crank drive not possible) - optionally radio-controlled with either a wall transmitter or a hand transmitter - optionally with bidirectional radio (Somfy iO standard) - iO allows integration into a smart home system and operation via the Somfy app - lateral zip guide of the fabric into the guide rail - optionally with D-valance (Variovolant, extendable up to 150 cm by crank) - choice of 650 colours for cassette and frame – at no extra charge - the installation height including cassette is only 16.4 cm The picture shows an under-glass awning with extendable Variovolant. The valance is attached to the front profile. The picture shows the front end profile without Variovolant. The picture shows the zip system connecting the fabric to the rail, viewed from below. Smooth running and precise guidance. The order width is always the centre-to-centre dimension, see measuring help. This corresponds to the centre of the fixing point of the guide rail brackets. The projection is the narrowest installation dimension in the direction in which the fabric extends, minus 2 cm. Advantages of a zip awning: - optimum fabric tension - no light gaps at the sides - can be made specially and exclusively as an under-glass awning with an additional Variovolant This system is also available as a 2-part shading unit.

Reflexa® replacement awning fabrics are always charged per square metre. All fabrics have a water-repellent (Teflon) finish. They are acrylic fabrics weighing approx. 290 g/m². You can order the valance straight or scalloped. Example calculation and measuring: fabric width e.g. 396 cm, projection (height) 203 cm + valance 19 cm high = order width 396 cm x order height 222 cm Shipping throughout the EU. The hems (into which the existing PVC cord/keder is inserted) are made 2.5 cm wide as standard. If you need a different size, please let us know as a special request. The full fabric selection can be found in the configuration. - plain fabrics - block stripes - multi-stripes

Order external venetian blinds with 50 mm aluminium slats here – small stack heights, a wide range of uses and many drive options. High-quality Reflexa® external venetian blinds with 50 mm aluminium slats, crank or motor operation, made in Germany and of the latest generation (180 degree tilt). At the bottom of this page (below the colours) you will find detailed technical descriptions and PDFs to print out. Prices for external venetian blinds with 50 mm slats are slightly lower than for the wider, flanged slats. Order in our shop and configure your new external venetian blind. The picture above shows the Reflexa® EMA 50 endless cord blind, which carries out all functions – tilting the slats as well as raising and lowering the blind. During installation the cord is led through the window frame (drill a hole through the frame or wall beforehand) and operated via a deflection pulley (included in the delivery). For endless cord gears and crank drives we always make the gear flush with the head rail. The pictures show the gear protruding. Changing from "flush" to "protruding" is easy during installation. Reflexa® endless cord operation is the best-selling version for 50 mm slats. Endless cord gears are an economical version of the external venetian blind. - 50 mm external venetian blinds are available with endless cord gear, crank drive, motor drive or radio-controlled motor; the manufacturer is always Reflexa. Reflexa® motor operation Crank operation We offer 50 mm slats up to a width of 500 cm (cord pull up to 300 cm width, endless cord gear up to 250 cm, crank and motor up to 500 cm width) and a maximum height of 360 cm. For larger blind sizes, please choose the 60, 80 or 88 mm slats, which are flanged at the sides. For protection against wind and weather, the 50 mm blinds can be made with lateral tensioning using a nylon-coated steel wire. For widths over 200 cm we recommend an additional central guide wire (wind protection). To cover the head rail and the slat stack when the blind is raised, an angle cover plate in a matching RAL colour can be fitted on top. The endless cord gear is durable and maintenance-free. Ladder tapes made of 100% Terylene. Head rail always in natural silver, 57 x 51 mm or 40 x 30 mm depending on the drive type. Bottom rail 51 x 20 mm, coated in a colour of your choice. Please note*: with small widths, the blind may hang slightly askew; this cannot be avoided. Please note: all order sizes are finished sizes of the blind, i.e. outer edge of slat to outer edge of slat = order width, and top edge of blind to bottom edge of bottom rail = order height of the finished blind. Wall fitting, so that the raised slat stack is out of the window's field of view. Side caps are required for the cover plate, see configuration. Order height (outside) = window opening height plus stack height plus 3 cm = order height of the external venetian blind Fitting options: ceiling, wall, recess Please note that only our measuring guide is binding for you. Any different measuring guides from manufacturers are not valid. We have written ours to be as easy as possible for a non-specialist to follow. If you have any questions, please call our telephone hotline. The following slat colours are available. Other slat colours can be supplied on request at no extra charge – just ask. Head rail always in silver. The bottom rail and tensioning brackets of the blind are silver, dark grey or white as standard. All other colours are available at a surcharge, see configurator. We are happy to send you the stack heights and specifications of the individual slat types on request.

Order and buy the Reflexa® LifeSmall under-roof awning up to 600 cm wide x 450 cm projection in our shop. Delivery to Switzerland and Austria is available. An under-roof awning is designed for situations where fitting over or on top of the roof is not possible for technical reasons. The LifeSmall is simply fitted underneath an existing roof structure, so the fabric is not exposed to dirt, wind load or moisture. A finished under-roof awning. The corner end profile runs right through to the end. - Standard frame colours white RAL 9016, silver RAL 9006, grey-brown RAL 8019, 3 grey metallic shades and any other RAL colour. All special colours at no extra cost - Somfy or ELERO motor fitted as standard - can also be operated by crank at a reduced price - high-quality awning fabric from the Reflexa® collection - from 450 projection = fabric support wire included to prevent the fabric from sagging - cassette height only 14.8 cm On awnings over 400 cm wide or 250 cm projection, increased and possibly noticeable sagging of the fabric may occur. This reflects the current state of the art and does not affect the function or use of the awning. In borderline cases, an additional fabric support wire can counteract this. (option in the configurator) (the centre distance varies depending on the drive, see drawings) Fitting on beams with crank drive TOP picture --- fitting on beams with motor drive. The minimum distances refer to the positions of the mounting brackets on the awning box. Measuring the projection for all types of fitting: - rear edge of universal bracket at the back of the awning box to front edge of guide rail (for recess fitting, we recommend deducting 1 - 2 cm) Measuring the width when fitting with reveal brackets: - inner edge of reveal to inner edge of reveal minus 8 cm for crank drive and minus 6 cm for motor drive (this is also the centre distance) Detail of the side guide rails and the end profile. Outside and inside view. Here you can see the rail holder and, below, the available reveal brackets. Summary of product features This under-roof awning is identical in construction to the T200 under-glass awning from the system supplier Varisol. You can configure this interior conservatory shading online and order it in our shop. In certain situations it may be necessary to split the awnings and fit them side by side. Coupled under-roof awnings are not possible for technical reasons. The price of this conservatory shading always depends on the width and projection. Another form of under-roof sun protection is the Plafond PL 11 pleated blind, which shades individual panes at low cost. Unlike the under-glass awning, the pleated blinds are operated with a hand operating rod. If you have any questions about the best shading for your property, we are happy to help by phone. For external conservatory shading, choose the Life conservatory awning For conservatory shading with variable guide rails for special shapes or sloping shading, choose the LifeFlex conservatory awning For free-standing conservatory-style shading without a glass roof, choose the Viladora pergola awning

Full-surface shading from Reflexa® for conservatory roofs, with no light gaps at the sides thanks to zip technology. The zip-like system prevents the awning fabric from sagging at the sides. Larger areas up to 12 m wide are possible, and the awning can also be used in locations exposed to wind. Configure and order this conservatory shading in our shop. Features and product details: - Somfy electric motor as standard - optional radio control with wall or hand transmitter - optional bidirectional radio for smart home integration and operation via app - zip side guides with no light gaps at the fabric - protective cover for the drop bar when retracted (closed cassette) - choice of 650 colours for cassette and frame – at no extra cost - brackets / mounting feet included - housing height only 144 mm - max. width 12 metres - single units up to 6 metres wide; wider only as coupled systems (on request) - large choice of fabrics Precise fabric guidance in the side rails thanks to the zip system. Standard spacer height = 10.5 cm (also available in 15 and 20 cm heights at extra cost)

Configure Reflexa roller shutters (Heroal system) in our shop and buy them made to measure online. High quality, made in Germany. Roller shutter box shape rectangular with a 28 degree bevel at the front as standard, or a round box at no extra charge. Aluminium curtain available at a 35% surcharge (all HEROAL® system) All guide rails (22 mm deep x 53 mm wide; with integrated insect screen roller 40 mm deep x 53 mm wide) have a rubber piping insert for quiet running of the curtain. Strap operation (or Elero® or Elero 868 ® motor and remote control at a surcharge). Supplied as standard with strap pull (possible up to 4.3 m²), strap guide roller and screw caps. The rails are supplied undrilled or drilled. Fixing screws for the building structure are not included. We cannot give a guarantee for PVC units larger than 3.5 m². Combination roller shutters with a double guide rail are pre-assembled with a continuous pelmet and delivered in one piece. Box and rail colour available in any colour at no extra charge The PVC curtain is a hollow-chamber profile, 37 mm high x 8.5 mm thick. The aluminium curtain is a foam-filled, insulated profile, 37 mm high x 8 mm thick. For the colour range see above. The configurator shows the matching box size automatically under “Your selection”. It depends on height, curtain and drive (Reflexa table 2026). Now also available with a spring-loaded insect screen roller. An additional roller is fitted at the top of the box. The guide rails then have a double track (towards the inside for the insect screen roller, outside for the roller shutter) For the surcharge for an integrated insect screen roller, see configuration. (including double guide rails and accessories) Standard roller shutter or roller shutter with fly screen. All roller shutters are available made to measure with either strap pull or motor drive. The roller shutters have passed a hail impact test. According to Reflexa, its roller shutters are made in Germany. Order in our shop and configure what you need. We also deliver to Austria, Switzerland and other selected EU countries.

Warmth on the terrace as soon as you switch on – no preheating. Reflexa's S1 and S3 heaters use the Solastar-G infrared tube, which reduces light emission by up to 99 %. The heater tilts up to 45° (one direction). The S1 with 1400 or 2000 watts comes with a bracket for wall or ceiling, quick clamp and a 50 cm cable with Schuko plug and Hirschmann coupling. With the support tube holder it mounts directly on a support-tube awning (not possible on Suntigua with crossed arms). The S3 with 2500 watts comes with a T-bracket for wall or ceiling and a 50 cm cable; it cannot be mounted on the awning. Connecting cables from 2.5 to 10 m reach sockets further away. To control the heater by radio you need the io dimmer module (3 levels: 33 / 66 / 100 %, up to 3000 W) and a Somfy io transmitter. Heaters, holders and dimmer module are available in RAL 9010, RAL 9006 and DB 703.

Replacement crank for Reflexa Plisseo pleated blinds with crank operation. Choose the length so that you can reach the crank comfortably – from 400 mm for windows at hand height up to 3000 mm for roof windows and high glazing. Colour grey.

Self-supporting sloping external venetian blinds are particularly suitable for fitting to glass façades and low-energy houses. Sophisticated shading for special fitting situations. This type of shading is needed where the building does not allow fitting directly to the façade or window frame. The complete construction consists of the sloping external venetian blind, guide rails and pelmet. An electric motor drives the blind and controls the tilting of the slats. The bottom rail is a telescopic rail that automatically shortens and lengthens as the blind moves up and down, depending on the angle required. This blind is only available with guide rails. Double, reinforced guide rail brackets hold the complete system and the factory-fitted U-shaped pelmet. Details and features: fitted with 80 mm nipple-guided flat slats, available in many colours available with an inclination of up to 45 degrees (full list at the end of this page) ELERO 230 V motor as standard radio control possible U-shaped square box pelmet to cover the slat stack included as standard (round version on request) side caps for the pelmet included as standard fully pre-assembled and ready to fit double guide rail brackets in various sizes guide rails, pelmet, bottom rail and spacers available in any colour at no extra cost guide rails available in round or square design guide rails always inside the pelmet Horizontal and vertical sectional drawings are provided below to help you with measuring. If you need technical support, please send us photos at: shop(at)sonnenschutzshop24.eu Please refer to the technical drawings for the measuring guidelines. All available slat colours for the Asyflex 80 NF self-supporting. Stack sizes and pelmet sizes – finished sizes with rail guidance: (parallel to the slope) 80 mm slats up to 120 cm blind height = 16 cm / 19 cm 80 mm slats up to 140 cm blind height = 17 cm / 20 cm 80 mm slats up to 160 cm blind height = 19 cm / 22 cm 80 mm slats up to 180 cm blind height = 20 cm / 23 cm 80 mm slats up to 200 cm blind height = 20 cm / 23 cm 80 mm slats up to 220 cm blind height = 21 cm / 24 cm 80 mm slats up to 240 cm blind height = 23 cm / 26 cm 80 mm slats up to 260 cm blind height = 24 cm / 27 cm 80 mm slats up to 280 cm blind height = 26 cm / 30 cm 80 mm slats up to 300 cm blind height = 27 cm / 30 cm 80 mm slats up to 320 cm blind height = 28 cm / 31 cm 80 mm slats up to 340 cm blind height = 29 cm / 32 cm 80 mm slats up to 360 cm blind height = 31 cm / 34 cm 80 mm slats up to 390 cm blind height = 33 cm / 36 cm Stack sizes and pelmet sizes with stainless steel rod guidance. (parallel to the slope) 80 mm slats up to 120 cm blind height = 15 cm / 18 cm 80 mm slats up to 140 cm blind height = 16 cm / 19 cm 80 mm slats up to 160 cm blind height = 17 cm / 20 cm 80 mm slats up to 180 cm blind height = 18 cm / 21 cm 80 mm slats up to 200 cm blind height = 19 cm / 22 cm 80 mm slats up to 220 cm blind height = 19 cm / 22 cm 80 mm slats up to 240 cm blind height = 20 cm / 23 cm 80 mm slats up to 260 cm blind height = 21 cm / 24 cm 80 mm slats up to 280 cm blind height = 22 cm / 25 cm 80 mm slats up to 300 cm blind height = 23 cm / 26 cm 80 mm slats up to 320 cm blind height = 24 cm / 27 cm 80 mm slats up to 340 cm blind height = 25 cm / 28 cm 80 mm slats up to 360 cm blind height = 26 cm / 29 cm 80 mm slats up to 390 cm blind height = 28 cm / 31 cm Manufacturing limits for sloping external venetian blinds: up to 190 cm width = up to 45 degrees inclination up to 200 cm width = up to 44 degrees inclination up to 210 cm width = up to 41 degrees inclination up to 220 cm width = up to 37 degrees inclination up to 230 cm width = up to 34 degrees inclination up to 240 cm width = up to 30 degrees inclination up to 250 cm width = up to 25 degrees inclination up to 260 cm width = up to 19 degrees inclination up to 270 cm width = up to 12 degrees inclination (only with rail guidance and 80 mm slats)

The Asyflex sloping external venetian blind is the ideal external sun protection and privacy solution for sloping windows and other special shapes. The Reflexa AsyFlex sloping external venetian blind is a versatile slat system. Thanks to a patented telescopic rail, windows and glazed areas with a pitch of up to 45 degrees can be shaded. Sloping external venetian blinds are becoming increasingly popular. Despite their high cost, they are almost indispensable in summer. They can be used in many different situations and you can configure them online with us. Sloping shading can be made as a roller shutter or as a venetian blind. Both systems are always electrically operated. For many years Reflexa® has been a pioneer in developing these complex external shading systems for sloping windows. Use our configurator and you will receive a competitive online price immediately. New: from 04/2026 the Asyflex 80 SMS can be ordered as a quick-fit system. Winner of the 2015 Innovation Award at the R+T trade fair. New: Asyflex with rail guide (nipple guide). The adjustable slat positions of the sloping external venetian blind allow almost unlimited control of incoming light. The adjustable aluminium slats look light and unobtrusive, which also makes them ideal for conservatories and glass extensions. They can be set anywhere from closed through half open to fully open. The AsyFlex sloping blind can also be combined with a matching straight external venetian blind. We are happy to advise you on planning. Design your façade without compromise. The wide choice of colours lets you combine the slats, pelmets and telescopic rails as you wish. Standard rails are T-groove guide rails. Blackout rails S70 are available as an option. Further features of the sloping external venetian blind: The slats are made from a curved special aluminium strip with a lightfast, corrosion-resistant paint finish. Available as an 80 mm flat slat (up to 270 cm width with rail guide). To cover the slat stack when the blind is raised, we can supply an L-shaped or U-shaped cover plate in a matching colour. For fitting in front of the house wall, the cover plate is supplied closed at the sides (with side caps). For fitting in the reveal, a cover plate open at the sides is recommended. Details of the Asyflex blind: the blind is guided at the sides by a stainless steel rod or by 25 x 25 mm side rails (80 mm slats only). Supplied as standard with a high-quality 230 V mains motor. The drive is pre-installed out of sight in the head rail. Delivery within Germany is free of charge, using the manufacturer's own vehicles at no risk to you. We deliver throughout the EU and to Switzerland. The production sizes are derived from these measurements (geometric shape). Deductions are made at the factory. When fitting in front of a reveal opening (on an open house wall), please allow for the necessary overlaps all round and for the stack sizes. All order sizes are finished sizes of the blind. The type of fitting must be selected in the configurator; this determines whether deductions are made or the sizes are taken as finished sizes. If you make your own deductions for fitting in the reveal, please note that this also changes the diagonal of the geometric shape, which in turn changes the heights accordingly. If you make a deduction from the base width, a new geometric shape must therefore be measured vertically upwards, which will not match the net dimensions of the actual reveal. Explanation of a sample external venetian blind and the corresponding stack and pelmet sizes: Stack sizes and pelmet sizes – finished sizes with rail guide: (parallel to the slope) 80 mm slats up to 120 cm blind height = 16 cm / 19 cm 80 mm slats up to 140 cm blind height = 17 cm / 20 cm 80 mm slats up to 160 cm blind height = 19 cm / 22 cm 80 mm slats up to 180 cm blind height = 20 cm / 23 cm 80 mm slats up to 200 cm blind height = 20 cm / 23 cm 80 mm slats up to 220 cm blind height = 21 cm / 24 cm 80 mm slats up to 240 cm blind height = 23 cm / 26 cm 80 mm slats up to 260 cm blind height = 24 cm / 27 cm 80 mm slats up to 280 cm blind height = 26 cm / 30 cm 80 mm slats up to 300 cm blind height = 27 cm / 30 cm 80 mm slats up to 320 cm blind height = 28 cm / 31 cm 80 mm slats up to 340 cm blind height = 29 cm / 32 cm 80 mm slats up to 360 cm blind height = 31 cm / 34 cm 80 mm slats up to 390 cm blind height = 33 cm / 36 cm Stack sizes and pelmet sizes with wire and stainless steel rod guide (parallel to the slope) 80 mm slats up to 120 cm blind height = 15 cm / 18 cm 80 mm slats up to 140 cm blind height = 16 cm / 19 cm 80 mm slats up to 160 cm blind height = 17 cm / 20 cm 80 mm slats up to 180 cm blind height = 18 cm / 21 cm 80 mm slats up to 200 cm blind height = 19 cm / 22 cm 80 mm slats up to 220 cm blind height = 19 cm / 22 cm 80 mm slats up to 240 cm blind height = 20 cm / 23 cm 80 mm slats up to 260 cm blind height = 21 cm / 24 cm 80 mm slats up to 280 cm blind height = 22 cm / 25 cm 80 mm slats up to 300 cm blind height = 23 cm / 26 cm 80 mm slats up to 320 cm blind height = 24 cm / 27 cm 80 mm slats up to 340 cm blind height = 25 cm / 28 cm 80 mm slats up to 360 cm blind height = 26 cm / 29 cm 80 mm slats up to 390 cm blind height = 28 cm / 31 cm Possible sizes of sloping external venetian blinds: up to 1876 mm width = up to 45 degrees pitch up to 1909 mm width = up to 44 degrees pitch up to 2003 mm width = up to 41 degrees pitch up to 2121 mm width = up to 37 degrees pitch up to 2202 mm width = up to 34 degrees pitch up to 2301 mm width = up to 30 degrees pitch up to 2408 mm width = up to 25 degrees pitch up to 2513 mm width = up to 19 degrees pitch up to 2601 mm width = up to 12 degrees pitch up to 2649 mm width = up to 5 degrees pitch New: now also available as the Asyflex 80 SMS sloping external venetian blind, quick-fit system

• up to 550 × 300 cm
• crank, motor, radio or solar
• optional Duomatic: tilt up to 55° by crank

• up to 550 × 300 cm
• motor, radio or solar
• 14 cm high cassette

• up to 550 × 300 cm
• crank, motor, radio or solar
• 13 cm flat cassette

• up to 700 × 400 cm
• crank, motor, radio or solar
• no visible screw fittings, optional Duomatic

• up to 700 × 400 cm
• crank, motor, radio or solar
• also with crossed arms or vario valance

We can offer Reflexa® hinged insect screen frames in 8 standard colours at no extra charge. Configure and buy in our shop. Profile colours available (white RAL 9016, anthracite RAL 7016, ochre RAL 8001, black-brown shade 8077, silver anodised EV1, anthracite metallic DB 703, brown RAL 8014 and matt bronze C33). The UV-stable piping is always black or grey and is matched as closely as possible to the frame colour. Max. width = 130 cm x max. height = 210 cm. The extruded aluminium frames have a high-quality coating and are torsionally rigid. A brush seal is fitted at the top and bottom, and a magnetic strip on the vertical closing edge. The counterpart of the magnetic strip on the window or door frame is self-adhesive and very easy to fit. The fibreglass mesh is either black or grey. The hinges are low-maintenance aluminium hinges. From a height of 150 cm, a handle bar is fitted as standard (handle bar width = 65 mm), which provides greater torsional rigidity in the middle section. For smaller heights, the frame is operated with a handle knob, see picture. No kick plate is fitted at the bottom of these hinged frames. Opening and closing is done exclusively via the 65 mm wide handle bar in the middle on doors and via the handle knob on windows. View from inside: this sample unit is under 150 cm high and is operated by a handle knob. Over 150 cm height = made with a centre bar.

Buy the extremely sturdy Reflexa® drop-arm awning in our shop. The sturdy drop arms provide stability, and the internal springs ensure optimum fabric tension. This allows a maximum width of 500 cm and a maximum extension of 150 cm. The standard extension angle is 90 degrees. For an angle of up to 120 degrees (surcharge), the fabric is made longer. Three different projections are available: 100 cm, 125 cm and 150 cm. The fabric selection is available in the configuration. Reflexa® fabric collection, 295 g/m², lightfast, Teflon-coated, high quality. Wall, ceiling and recess fitting (recess brackets at extra cost) is very quick: the awning is simply hooked onto brackets already fixed on site. All RAL frame colours at no extra charge, including white, silver, brown, anthracite, DB 703 etc. Supplied without valance as standard; a valance is available at extra cost. Choice of crank or motor drive. A rain canopy is available as an option; it is supplied with side caps and approx. 5 cm wider than the awning width. Free delivery within Germany with a Reflexa® works vehicle. Ceiling and wall brackets included, but without fixing screws into the building structure. Intermediate sizes are charged at the next higher table price, with no surcharge. Can be made accurate to the millimetre. All prices are delivered prices for self-installation, i.e. free delivery within Germany. Configure your new drop-arm awning in our shop and order with free shipping. Delivery to the EU and Switzerland is possible at extra cost.

These insect screen frames are mainly used where the sash rebate is slightly angled and the window closes flush without any protruding parts. Fitted in the clear sash opening. The smallest size of the hook-in brackets is 14 mm. Fixed brackets at the bottom and pivoting brackets at the top for easy hooking in. The profile itself is just 10 mm thick. We can offer the Reflexa® Flylock® fixed-frame insect screens in 8 standard colours at no extra cost (white RAL 9016, anthracite RAL 7016, ochre RAL 8001, black-brown shade 8077, silver anodised EV1, anthracite metallic DB 703, brown RAL 8014 and matt bronze C33). The UV-stable keder is always black or grey and is chosen to match the frame colour as closely as possible. Max. width = 230 cm x max. height = 230 cm. A crossbar is fitted above 120 cm height / width. The extruded aluminium frames have a high-quality coating and are torsion-resistant. A brush seal is fitted all round. The fibreglass mesh is either black or grey.

The new blackout external venetian blinds from Reflexa®, with the 71 mm V-slat as type EL71 N, can be configured made to measure and ordered online in our shop. Thanks to the special curvature of the slats, near blackout can be achieved. Fitted without spacers. The new S-guide rails are used. Soft closing thanks to rubber seals between the slats. All guide rails can be ordered. Standard or S70 blackout rails. (selectable in the configurator) If you have any questions about your planning, we will be happy to help. Shipping and delivery with our own vehicles, on request also to Austria and Switzerland as well as selected EU countries. The new V-slat type EL71 N with rail guidance and almost complete blackout. Max. width 470 cm x 400 cm height. Harmonious appearance thanks to perfect workmanship. Even, neat stacking of the slats. Stack sizes of the complete external venetian blind when fully raised. Measurement basis is top edge of head rail to bottom edge of bottom rail. up to 100 cm total height = 15.1 cm stack up to 120 cm total height = 16.5 cm stack up to 140 cm total height = 17.9 cm stack up to 160 cm total height = 19.7 cm stack up to 180 cm total height = 21.1 cm stack up to 200 cm total height = 22.5 cm stack up to 220 cm total height = 24.3 cm stack up to 240 cm total height = 25.7 cm stack up to 260 cm total height = 27.1 cm stack up to 280 cm total height = 28.9 cm stack up to 300 cm total height = 30.3 cm stack up to 320 cm total height = 31.7 cm stack up to 340 cm total height = 33.5 cm stack up to 360 cm total height = 34.9 cm stack up to 380 cm total height = 36.3 cm stack up to 400 cm total height = 38.1 cm stack Factory pelmet size = plus 2.5 cm added to the height. Fitting options: ceiling, wall, recess For additional blackout of a window with blackout slats, choose our good-value blackout external venetian blind.